Jump to content
SAU Community

Recommended Posts

Please excuse my ignorance, but I just saw this article:

http://formen.ign.com/news/16796.html?fromint=1

And it mentions the motor:

The Skyline GTR’s race-tested RB36DETT DOHC, 24 valve 2.6 liter intercooled, twin-turbo I6 at a very conservative 280 base horsepower and a very respectable 289 lb/ft of torque.

This is a typo right? What is the biggest RB motor out there?

Link to comment
https://www.sau.com.au/forums/topic/34579-rb36dett/
Share on other sites

Please excuse my ignorance, but I just saw this article:

 

http://formen.ign.com/news/16796.html?fromint=1

 

And it mentions the motor:

 

 

This is a typo right? What is the biggest RB motor out there?

By the sounds of the article, they are refering to the RB26DETT so it looks like a typo. No such thing as an RB36DETT.

Link to comment
https://www.sau.com.au/forums/topic/34579-rb36dett/#findComment-691925
Share on other sites

While we're kind of on the topic, what's the biggest RB engine you could make? e.g. RB30 block, RB26 head etc - no idea what crank and other parts you'd need, but roughly how big could you make one. I realise it would totally change the nature of the engine if it was 3.5L or so, but I'm just kind of curious.

Link to comment
https://www.sau.com.au/forums/topic/34579-rb36dett/#findComment-691943
Share on other sites

We have tried up to 3.3 litres - we could have gone more, but it was diminishing returns, hence pointless.

Just for completeness, we also went as low as 2.4 litres...

Mario.

I suppose it does make sense that if you're increasing the stroke it wouldn't be as easy to rev as hard. Also, you aren't really increasing the volume of the engine that much % wise once you are adding only a few tenths of a litre.

How did the GTR respond to the reduced capacity? I think it was Nismo that reduced the capacity of a VH45DE to 3.5L and it revved like an F1 car. Your GTR already is a very revvy machine, so it must have been even better at 2.4L. If I remember correctly, you were having trouble shifting at very high revs at some point (my memory is bad, sorry). Did it make shifting harder?

Link to comment
https://www.sau.com.au/forums/topic/34579-rb36dett/#findComment-692028
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I refer you to this thread on PF, by someone who knows what he's doing. Paints a good picture of the humble AD09.
    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
×
×
  • Create New...