Jump to content
SAU Community

Recommended Posts

scan0001.pdf Hello All,

I have a BNR34 red top engine for sale, it is one of the few that can have its history certified. I is in a 99 V-spec GTR that was imported into Australia in the early 2000's. I have the original dash at 17,000kms and a Nismo 320km dash sitting at 112,000 in the vehicle currently. The engine has been serviced religiously at 5,000k intervals and uses no oil, the only engine mods were HKS cam gears that weren't dialed in and a N1 water pump when the timing belt was replaced 5,000kms ago. Outside of that it ran a HKS EVC, Garret 7's, Pods and Apexi FC, all to put a modest 389 hp out at the wheels.

We were looking to rebuild the engine, but have decided to go with a N1 power plant instead.

There is an issue with the engine, number 5 cylinder is running low on compression 12% out, the guys at X-speed believe it to be a cracked ring. So if anyone is interested this engine would suit a rebuild, we are looking for offers now as you will be able to see and feel how the engine is running and make a decision based on that. I have no doubt this engine will run as it is for another ten years, it runs perfectly the only telltale is that is was breathing a little heavier than normal under boost at 17psi.

Engine location is Perth WA, please get in touch if you are interested. I am being completely transparent here, I have no doubt I could sell this engine for a lot more without disclosing what I know about it. If you would like to chat to the cars mechanics re the engine, please contact me first thanks.

Link to comment
https://www.sau.com.au/forums/topic/346142-rb26dett-for-sale/
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

Has the engine been removed?

Pics would also be helpful..

Engine is still running in car, as far as pics go if you want I can email, but it is like any other red top rb26

I'm interested as well. Looking at a build but want to still drive the line. As per previous post, what does it come with?

PS I'm south of you so can pick up to avoid transport issues.

Edited by RichyR32GTR
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...