Jump to content
SAU Community

Recommended Posts

thanks. i'm really no good at these sort of things, my friend bought me some nice JL 6x9's for the rears. i had some boxed 6x9's which came with the car, those carozerria or whatever ones and thought that the new ones would pop in the hole. should've known that the hole size is still for 6". now im wondering if i should get him to exchange the 6x9's for 6". or modify it somehow.

Link to comment
https://www.sau.com.au/forums/topic/34647-6x9s-in-the-rear/#findComment-693026
Share on other sites

yes same in vic u cannot cut the parcel shelf at all as it is supposedly a main structure in the car which supports the rear windscreen. If u wanna run the risk then do it but i'd just get pods made up from fibreglass, they don't look all that good but i wouldn't run the risk.

P.S. i was also told that you are allowed to cut the parcel shelf but the hole size i do not know and it must be further than 11 cm from the child restraint. (Dunno if thats tru, but thats of no help any way to your cause)

cheers,

Rom.

Link to comment
https://www.sau.com.au/forums/topic/34647-6x9s-in-the-rear/#findComment-693464
Share on other sites

I had the same problems, but i have 7x10's and every audio shop i took it too refused to even try to install them (all afraid of a little hard work). But i eventually moved the hicas computer and slid them right in, there was about 3mm to spare between the speaker magnet and the battery fastner, but i am here to tell you it can be done

Link to comment
https://www.sau.com.au/forums/topic/34647-6x9s-in-the-rear/#findComment-696783
Share on other sites

the hicas computer is easy to move.... it just unscrews then you can screw it down again on the base of the shelf.... i have no idea why the people at nissan designed the boot the way they did.... every other part of the car is made with the idea that people will add to it, but the boot just seems inefficient to me, especially the tiny speaker holes and the positioning of vital equipment (hicas and battery) directly benieth the speaker holes, when there are many other places that they could go.

Link to comment
https://www.sau.com.au/forums/topic/34647-6x9s-in-the-rear/#findComment-698338
Share on other sites

Hi

I added 6 x 9 speakers to my R33 by making up an MDF spacer that went under the standard parcel tray, then traced that onto the underside of the tray, enlarged the ho;es for the stock speakers, and found that with a little careful positioning the standard grilles covered the new speakers.

Voila - stealthy 6 x 9's

Link to comment
https://www.sau.com.au/forums/topic/34647-6x9s-in-the-rear/#findComment-698781
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...