Jump to content
SAU Community

Recommended Posts

Hi guys. As the title says i'm putting a series 1 rb25 into my r32 gts-t. At present i already have a EMS stinger 4 wired in running my rb20. At this stage i'm thinking its easiest to stick with my current loom and swap any sensors i can off my rb20 and put them on the rb25. i'm guessing this isn't possible with anything (aac valve?) which i would need to get wired up separately. I'm using my top feed injectors as i got a top feed fuel rail with greddy copy inlet manifold. I did get a engine loom connected to the rb25 when i got it but as it came out of an r31 ( It was running no prob in the 31) its messy with bits hanging out here and there and i dont know if anything important has been disconnected.

Whats people thoughts: is it worth using the rb25 engine loom and getting that wired into my car and the EMS?

i see someone on here selling a rb25 s1 engine loom that is suppose to be a straight plug in to a 32. not sure if it would be worth buying that but then i would need to get that wired into my EMS. Just thinking you could be buying someone elses problems and the money better spent wiring up what i got.

Can anyone recommend someone in adelaide that really knows these conversions (wiring side).

So far i've been getting my tuning done at boostn oz and so far i don't have any complaints.

Also just wondering about wiring in the 25 box.

My mate and i doing all the mechancial side of things just not sure about the wiring.

Any thoughts are appreciated i just want to do it the simplest way.

Link to comment
https://www.sau.com.au/forums/topic/348146-rb25-s1-into-r32gts-t/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...