Jump to content
SAU Community

Recommended Posts

R33 GTR alternator $40

R33 GTR starter motor $40

R33 GTR power steering pump $40

R33 GTR air con compressor pump $40

R33 GTR engine mount brackets $40

R33 GTR custom dual 2.5"front pipes to tip exhaaust, mild steel, front pipes welded on, with 2x mini race cats on each front pipe, no rear muffler fitted but have this if you dont like the straight pipes, dual 2.5" straight pipes, sounds angry & tough $500

R34 GTR oem alloy radiator FREE

R33 RB25 bare OEM plenum (top & bottom pieces only) FREE

R33 RB25DE/T S1 injector loom intact & uncut, all clips in good condition $40

R33 RB25DE/T IAC valve $30

DSC_3404.jpg

R33 RB25DE/T AIR REGULATOR $30

DSC_3402.jpg

S14 SR20DE/T AFM + rubber intake pipe, welcome to try before you buy but removed due to z32 upgrade $40

walbro GSS342 255lph fuel pump x2, purchased new to test to see if the old one was faulty but it wasn't, less then 100km usage on each pump $50ea

fuel pump only, no fitting kit.

Cusco catch can - used, has scratches & can do with a clean$20

2x ford territory 17x7 rims with skid tyres $40

Toyota Supra JZA80 top secret fibreglass front bar, brand new & unfitted $150

Toyota Supra JZA80 stock exhaust $150

OIL COOLER KIT - braided lines + earl fittings (lines have rubbed against chassis causing minor wear & tear, blue alloy core; came off a SR20DET 180sx, NON RELOCATION & NO THERMOSTAT $100

24pi53s.jpg

**wear & tear bits**

301iwxk.jpg

Z32 AFM plug, missing the metal clip $25 delivered

random NISSAN OEM gaskets left over from my engine rebuild gasket set, its got headgasket, exhaust manifold & inlet gaskets, oil pump gasket + few other randoms $40

R33 GTS-T 5-bolt half shafts, surface rust from being outside $70

dual 60mm a-pillar gauge mount, came off a R33 GTS-T $20

thats all i can think of for now, will update once i come up with more sh*t to clear out.

all prices are exclusive of delivery unless stated

pics up when i get the chance.

all parts are located in Sydney.

will post certain things, please PM if you are interested in anything.

happy new year.

Link to comment
https://www.sau.com.au/forums/topic/348956-garage-clean-out/
Share on other sites

Can you pm a total price for the p/s pump And gtr radiator (if it's in ok condition) plus postage to 5047 south oz

cheers mate

Edited by -RBD2-

sorry forgot to state that

random NISSAN OEM gaskets left over from my engine rebuild gasket set, its got headgasket, exhaust manifold & inlet gaskets, oil pump gasket + few other randoms $40

is to suit R34 RB25DE/T and R33 Rb25DE/T bar the inlet gasket.

STOCK RB25 PLENUM GONE

cheers

  • 1 month later...
  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...