Jump to content
SAU Community

Recommended Posts

Hey everyone!

Soo last time I got around to putting a post up, i had sweet f a access to teh nets and well 3 mobile was being ....... well was just being super gay so to whoever I didnt get back to, you now know why.

Anyways heres the DL

I have one damaged A31 and one A31 Shell

Note the damaged cefiro has been hit quite hard at the front so no forward panels are of any use besides maybe being used as a UNIQUE paper weight lol

What I do have available from the damaged cef is as follows -

Interior wise I have just about everything, what isnt cracked/damaged inside will be forsale.

Exterior wise I have all doors w/ glass and electric window motors etc all working. Glass in clean (NO TINT) and panels are straight.

Boot lid

Factory front and Rear bumpers, both need paint, front is in OK condish, rear is perfect.

Rear window glass w/ wiper.

Now as for the cef shell -

Weld in halfcage

Boot

Bonnet with bpin holes

front drivers , front passenger and right rear passenger door w/ glass

Rear glass , wiperless

Now some other spare I have are as follows -

Cefiro dashmat in good cond

S1 Projector lights w/ black backing and side repeators

twin hole grille x 2

1x complete set of coilovers w/ adjustable tops

Sooo thats off of the top of my head, I will more than likely have other parts available.

Please TXT to my mobile or last resort send me a PM and will get back to you asap, which is more than likely in the evening.

All parts are located in Perth WA and can organise frieght at buyers expense.

Thanks so much,

Tales

0430-124-417

Link to comment
https://www.sau.com.au/forums/topic/349462-fs-cefiro-partsaurus/
Share on other sites

Im working on it although its difficult to put a price tag on items that you dont know that value of =/

Anyone feel free to pm me with some information, it would be greatly appreciated =)

Complete doors and glass still fs.

Grey interior in great condish.

Bonnet with bonnet pins, great condish in primer ready for paint.

Bootlid.

Front projector lights with black backing still fs.

Random bits of trim, power window switches etc still here

RB20DET cylinder head good cond.

Rb20DET coilpacks, good working condish 60.00

GT2871R kit, with 20 manifold gaskets, no lines 1000.00

2 x s1 grille, ok condish

Have front and rear glass wiperless. Give me a good offer and will have proffessionaly removed and shipped to you.

Have a pair of 25mm over fenders that require holes to be drilled and vents to be cut out. fiberglass job. 100.00 slight crack in one.

  • 2 months later...

gday there tales , how are ya buddy , hope all is well , i tried to contact you before regarding some of the above parts i need

i was wandering on your cefiro rolling bare shell , is the passenger side rear quarter in good condition as well as the front windscreen on the same shell in tact and no cracks watsoever ?

if you can do me a deal on that shell , i am more then happy to organise some freight to pick it up from where you are to get it shipped back here to sydney

hope you can help me out and sort this out so it gets out of your way

cheers anthony

btw 1 more thing and if you can quote me on the stock rear bar for the cefiro man

thanks again for your time

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...