Jump to content
SAU Community

Recommended Posts

$12500

TXT 0435509050 as I dont get service at home.

Selling as I will be a student as of the start of Feb and wont have the money to keep both cars on the road.

WILL NOT COME WITH STEREO

I have for sale my 91 180. I have owned it since 2008 when it was an auto CA18. Since then I put my Neo engine in that I have owned since it had 50000km on the clock, it now has 90-95k, and has been serviced by me EVERY 5k.

Already had 100k Service

Body has 86k on the clock.

All engineered and road legal

Reg runs out at the end of Jan will come with plates and roadworthy.

Pics are a few months old so have tidied up wiring around battery a little, still a little bit of tidying to do, and has had new tint put on a little darker

It has:

  • Gates Racing timing belt, idler, tensioner and Genuine Nissan R34 water pump and front 3 oil seals 6k ago.
  • PWR 44mm Rad. with a 10" and 12" SPAL thermo 12Mths old
  • Front mount with custom alloy piping
  • R33 5 speed with approx. 72k
  • Tein coilovers all round
  • R32 gtr brakes all round
  • r33 bm44 Master cylinder
  • 5 stud conversion with s14 hubs, knuckles and lca, and r33 rear.
  • r33 stockies with decent rubber
  • Genuine HKS SSQV
  • Momo steering wheel
  • blitz boost controller never run over 11psi.
  • cheap turbo timer but does the trick.
  • 52mm water temp,boost gauge and taco, taco not hooked up as real drivers dont need one! (stock taco works but reads 1/3 more, and stock speedo works but reads half as much, does come with jaycar corrector just not installed).
  • Ultra lightweight chromoly flywheel with exedy clutch plate and heavy duty pressure plate.
  • Bosch fuel pump 040/044 whichever is the intank.
  • Kouki light conversion
  • 3 inch exhaust turbo back
  • HUD works
  • Oil catch can

There is probably more but thats all I can think of at the moment

The bad,

  • Clear is fading on the roof
  • last owners bog holes from spoiler are lifting
  • kouki taillight trim isn't paint matched
  • one rather long crack on the dash above cluster.

Have been quoted 550 to repair bog in the boot, paint match hatch and kouki lights abd paint roof black.

Will swap for road bike no smaller than 600 + cash my way depending on whats on offer

post-40523-0-83930900-1294911081_thumb.jpgpost-40523-0-07817000-1294911095_thumb.jpgpost-40523-0-92260600-1294911104_thumb.jpgpost-40523-0-19052400-1294911161_thumb.jpgpost-40523-0-51387200-1294911186_thumb.jpgpost-40523-0-13746100-1294911214_thumb.jpgpost-40523-0-94024300-1294911225_thumb.jpgpost-40523-0-50006500-1294911236_thumb.jpg

Edited by ForceFedVL
Link to comment
https://www.sau.com.au/forums/topic/350247-rb25-neo-180sx/
Share on other sites

  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...