Jump to content
SAU Community

Recommended Posts

$12500

TXT 0435509050 as I dont get service at home.

Selling as I will be a student as of the start of Feb and wont have the money to keep both cars on the road.

WILL NOT COME WITH STEREO

I have for sale my 91 180. I have owned it since 2008 when it was an auto CA18. Since then I put my Neo engine in that I have owned since it had 50000km on the clock, it now has 90-95k, and has been serviced by me EVERY 5k.

Already had 100k Service

Body has 86k on the clock.

All engineered and road legal

Reg runs out at the end of Jan will come with plates and roadworthy.

Pics are a few months old so have tidied up wiring around battery a little, still a little bit of tidying to do, and has had new tint put on a little darker

It has:

  • Gates Racing timing belt, idler, tensioner and Genuine Nissan R34 water pump and front 3 oil seals 6k ago.
  • PWR 44mm Rad. with a 10" and 12" SPAL thermo 12Mths old
  • Front mount with custom alloy piping
  • R33 5 speed with approx. 72k
  • Tein coilovers all round
  • R32 gtr brakes all round
  • r33 bm44 Master cylinder
  • 5 stud conversion with s14 hubs, knuckles and lca, and r33 rear.
  • r33 stockies with decent rubber
  • Genuine HKS SSQV
  • Momo steering wheel
  • blitz boost controller never run over 11psi.
  • cheap turbo timer but does the trick.
  • 52mm water temp,boost gauge and taco, taco not hooked up as real drivers dont need one! (stock taco works but reads 1/3 more, and stock speedo works but reads half as much, does come with jaycar corrector just not installed).
  • Ultra lightweight chromoly flywheel with exedy clutch plate and heavy duty pressure plate.
  • Bosch fuel pump 040/044 whichever is the intank.
  • Kouki light conversion
  • 3 inch exhaust turbo back
  • HUD works
  • Oil catch can

There is probably more but thats all I can think of at the moment

The bad,

  • Clear is fading on the roof
  • last owners bog holes from spoiler are lifting
  • kouki taillight trim isn't paint matched
  • one rather long crack on the dash above cluster.

Have been quoted 550 to repair bog in the boot, paint match hatch and kouki lights abd paint roof black.

Will swap for road bike no smaller than 600 + cash my way depending on whats on offer

post-40523-0-83930900-1294911081_thumb.jpgpost-40523-0-07817000-1294911095_thumb.jpgpost-40523-0-92260600-1294911104_thumb.jpgpost-40523-0-19052400-1294911161_thumb.jpgpost-40523-0-51387200-1294911186_thumb.jpgpost-40523-0-13746100-1294911214_thumb.jpgpost-40523-0-94024300-1294911225_thumb.jpgpost-40523-0-50006500-1294911236_thumb.jpg

Edited by ForceFedVL
Link to comment
https://www.sau.com.au/forums/topic/350247-rb25-neo-180sx/
Share on other sites

  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Given you're running a 2.8 and my 2.5 is not really like for like, I suspect there could be a bit more timing you could give it. What is the kW yield per degree you're putting through it? Here's my E85 map to give you an idea, where it was I could still get another 3~4kW per degree thrown at it.  
    • It turns out that Setrab make a fan specifically for the oil cooler which is great and I've installed it with minimal swearing. I removed my 2x 12in push fans from the front of my aircon condenser and wired them into this. My main thermo fans kick on when I use the aircon anyway and would effectively already be working as puller fans through the condensor which is infront of the rad. The push fans (understandably) didn't really do much in the config they were previously in so now they're out. Now we're on to the "Oil fan doesn't really do much either!". Yes I'll duct it next if it does nothing in heavy use which it shouldn't. But hey, the object exists and fits great and is cool. Let me have this. The car is still in the "do my fittings leak oil now? do my wheels actually rub?" phase. I did a spirited drive on them and didn't hear or feel anything. Then I got back home and noticed there were grind marks on the inside of the rims, though I couldn't see where they were touching I got out the grinder and attacked the suspects. Note: I do not know how to use a grinder. Then I realised I had dragged my new rims across my concrete driveway before I did this drive. I didn't think I had damage at that time when I briefly looked...... but remembered this occurred after I did all the angle grinding. The grinding on the wheels in some very specific spots. It's not around the whole rim for example, which lines up with dragging it across concrete more than hitting a suspension component for even 1 full rotation. So everything is currently painted and taped up and I need to test it some more to see if it really IS rubbing, but from inside the car it doesn't feel like it is. In other news I attempted to do a before and after comparison of the heads/cam upgrade thing. Dynos lie, everything is in different measurements. Here is the data from the sandown back straight. Car go faster than before. Vroom vroom.
    • Here's my base ignition. +3 correction to redline when shooting water/meth which is always on. Looking at my old ignition table, I should be able to add 1-2 degree's next time I'm on the dyno.  Let me know your thoughts. 
    • Given what I know now - same haha, but this was 12 years ago with second hand 740cc Nismo injectors in my S15 daily, I was too busy hunting elsewhere for the issue to even look at the injectors, running through some cleaner was a happy coincidence haha
    • Not a terrible idea. But if I ever had concerns that my injectors were sufficiently dirty to be causing me a problem, they would be out of the engine and onto the actual injector cleaner/testing bench.
×
×
  • Create New...