Jump to content
SAU Community

Recommended Posts

hi all, i have an r33 rb25det with exhaust, bigger intercooler, blitz boost controller, splitfire coilpacks, and adding a safc within the next 2 days or so to try to stop it from running to rich.

does anybody no the air fuel ratio for a 25 running 10 psi?

Link to comment
https://www.sau.com.au/forums/topic/350560-r33-safc-tunes/
Share on other sites

as for what it is currently running now i'd say probably around 10.5:1 at high rpm. tuned you want it around 12:1, however when tuning with a safc you also end up altering the timing so you may not get it that lean. you might only get it to about 11.5:1 before it starts to ping. either way, a tuner should be able to sort it out for you since they will have a wideband o2 sensor to measure it (don't try and tune it yourself without one).

Link to comment
https://www.sau.com.au/forums/topic/350560-r33-safc-tunes/#findComment-5628644
Share on other sites

hence why you also use the apexi sitc, to be in control of the timing change(s)

safc + sitc with z32 afm = good combo

ran this myself, however changed out for AEM f/ic-8 (like greddy emanage ultimate) when upgraded to GT30 turbo

Link to comment
https://www.sau.com.au/forums/topic/350560-r33-safc-tunes/#findComment-5628957
Share on other sites

i wasnt aware the safc altered timing. How does it do that?

you are altering the AFM signal. generally the AFM voltage is used as the load scale and the RPM as the other scale. if you alter the AFM voltage you then alter the load scale and since the timing varies depending on the load, you end up altering the timing. most people don't realise this so if they do it themselves they may get the AFR's right but have the car pinging because they weren't paying attention to it.

Link to comment
https://www.sau.com.au/forums/topic/350560-r33-safc-tunes/#findComment-5629805
Share on other sites

  • 3 weeks later...

ah yes. that makes some sense.

Gotcha. good description.

you are altering the AFM signal. generally the AFM voltage is used as the load scale and the RPM as the other scale. if you alter the AFM voltage you then alter the load scale and since the timing varies depending on the load, you end up altering the timing. most people don't realise this so if they do it themselves they may get the AFR's right but have the car pinging because they weren't paying attention to it.

Link to comment
https://www.sau.com.au/forums/topic/350560-r33-safc-tunes/#findComment-5654543
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...