Jump to content
SAU Community

Decided On My Rims

Juz

By Juz,
in Exterior & Interior Styling

 Share

Recommended Posts

75coupe Grand Master

75coupe

Posted
Posted (edited)

no I dont would think so.... front and backs would stick out a bit I think...

+22 or +28 would beeasier to fit but still would need to be lipped and flared possibly...

Im suthere are more knowledgeable people on here that can be sure of that but Ive been looking at 17x9.5 all round on gtst and figured they would need to be between 22-28 offset and still need guard work...

Edited by 75coupe
Husky33 Veteran

Husky33

Posted
Posted

I have 9's +22, and the fronts stuck out just a little bit before i had the guards rolled and pulled slightly.

I am running 245's front and 255's rear, none of this stretched crap, and you def have to roll them. It doesn't hit the lip, but under hard braking and cornering it would. Also had to modify the splash guard on the front as it was rubbing.

If you want to lose the point of a performance vehicle and stretch the tyres, then you could get away with a lower offset, but the wheels will still stick out on stock guards

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted

will fit easily and has been done many many many times...

up front guard liners will have to be removed and the guard pulled a lil depending on tyre size (i'd recommend 235/45/17)

out back the lips will need to be rolled only and it will fit with a 235/45/17

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...