Jump to content
SAU Community

Hks Ssqv

<<<aZn_RoMeO>>>

By <<<aZn_RoMeO>>>,
in Engines & Forced Induction

 Share

Recommended Posts

<<<aZn_RoMeO>>> Collaborator

<<<aZn_RoMeO>>>

Posted
Posted

hey fellas,

does anybody kno how to set the ssqv hard n soft settings?

cos there was heaps of hissin noise under d bonnet n thought it was set too soft ppl say vacuum leak or sumthing, so thought i'd give it a go.

now its gettin really confusing and i can't even get it to sound like it did be4. i turn the screw clockwise go for a drive thinking its harder setting, then go back turn it the other way, and i can't tell the difference!!!!

now its just a flutter then the whistle then the normal pssht sound.

can someone tell me roughly which way and how much to turn to get it so it doesn't leak under vacuum and have dat long loud whitle metallic sound back?

thanks lot man.

Link to comment
https://www.sau.com.au/forums/topic/35208-hks-ssqv/
Share on other sites
krzysiu Grand Master

krzysiu

Posted
Posted

I used to have a HKS SSQV on my r33 GTS-T. As far as im concerned that blow off valve when i had it never made a Psssht noise. The HKS makes the higher squeel and then flutters. I loved that sound then had to get it replaced to a stock BOV. "They" told me my car was over modified and i couldnt have it. The engine stalled when i pulled up to lights and went off. IM still trying to make a HKS BOV work on my car without it goin off.

Link to comment
https://www.sau.com.au/forums/topic/35208-hks-ssqv/#findComment-704148
Share on other sites
<<<aZn_RoMeO>>> Collaborator

<<<aZn_RoMeO>>>

Posted
  • Author
Posted

yea i did some kind of setting that made it do that pssh noise after the wistle. sounds crap.

can u tell me which way the screw is meant to be turned for hard and soft? cos its really kinda confusing.

oh but. today i snapped the bolt. =(

anyone kno is u can just remove it and put in a new one?

Link to comment
https://www.sau.com.au/forums/topic/35208-hks-ssqv/#findComment-704431
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...