Jump to content
SAU Community

Recommended Posts

Heya guys, still selling all the parts from the r33, if you need anyhting specific please let me know, have got all pannels, interior bits and pieces, interior is all mint s2 stuff. Everything needs to go QUICK!!! Leaving overseas on 1st MAY!!

Manual conversion kit comes with:

R33 s2 RB25DET Manual Gearbox 85,000kms

Short Shifter

Slave Cylinder

Clutch Fork

Gearbox Crossmember

Manual Clutch and Brake Pedals

Clutch Master Cylinder

Manual Tailshaft (2dr)

Speed Sensor

Steel Braded and ADR Approved (HEL) Master to Slave clutch Line

Drivers side Gearbox loom to run manual transmission on automatic

Rubber Floor Boot

Interior Shifter surround console with leather boot

MISSING CLUTCH, WILL NEED TO SOURCE YOUR OWN!!!

- $1750

OR I can include an ORC 409 series single plate clutch as well for $2000 all up however clutch is not recommended for street (solid unsprung center)

Manual kit now with Exedy heavy duty clutch and rb20/25 flywheel, clutch has seen better days but will get you going and be ok for a little while but id recommend replacing disc before install.

2 x used Bridgestone Potenza Re55 Semi Slicks for sale 235/17/45 rrp $500+ each

1 has slight camber wear but still plenty of track life in these tyres, plan was to use them on the track day but didnt end up chucking them on, would probably last a couple of track days

$400 for pair, pm me

post-72541-0-97697600-1334883008_thumb.jpg

post-72541-0-92343900-1334883009_thumb.jpg

wanted: r33 non turbo (twin pot) front calipers. SA

cheers 0409466541

also for sale s15 4 pot front calipers + near new discs ( no pads). also have master cylinder and rears + discs but 1 caliper is missing the sliding bracket. $400 the lot

Edited by OUTATIME

FOR SALE: Full set of (5 x 114.3) "M2's" in electric arctic blue.

rears: 18 x 10 + 20

fronts: 18 x 9 + 15

$1,300 firm.

Time for me to change things up a bit and get some new rims going.

Pm me if your interested

Cheers

post-57119-0-58643600-1335091806_thumb.jpg

post-57119-0-39172300-1335091944_thumb.jpg

post-57119-0-81698700-1335091957_thumb.jpg

Hi my mates motor up for sale Rb20det

Up for sale is rb20 package, I recently inspected the engine while it was in a r32 skyline. I've personally seen it running and heard it idle. No unusual sounds at all, idle's perfectly.

Has rb25 turbo setup on it, unsure of condition of turbo. This price includes loom + ecu and everything you need to get it running.

Perfect engine to just chuck in and have a blast

$850 ono

Don't hesitate to contact him on:

0433362823

Thanks

  • post-81807-0-12440800-1334571556.txt

Up for sale is my motor and box, loom, ecu ect ect out of my r32 as i am upgrading to an rb25 set up, the motor is still in the car so can be seen/herd running and test driven. it runs smooth and never had a problem with it. Im after $1400 for it all cheers nick 0414450101

Located in blakeview 5114

i have a clarion vz400a car dvd player.

full ipod control

usb cable

its single din flip out

has remote and box

only 2months old.

this model:

http://clarion.com/au/en/products/2010/multimedia/multimedia_source_units/VZ400A/au-en-product-pf_1259413421612.html

only selling due to wanting double din.

$350

Up for sale is my Rb20det motor and box, loom, ecu ect ect out of my r32 as i am upgrading to an rb25 set up, the motor is still in the car so can be seen/herd running and test driven. it runs smooth and never had a problem with it. Im after $1400 for it all cheers nick 0414450101

Located in blakeview 5114

****** R34 GTT PARTS FOR SALE & ALSO EOI !! *******

Ok so i have the Following up for grabs.

- R34 GTT Side mount Intercooler with piping $150 ono $80 ( Great Upgrade for older skylines 33,32 ect ) P.s handy for Regency

- R34 GTT series 2 Front bar with Genuine skyline grill,Indicators and badge $150 ono $100 ( Give your ride that Rare & unique newer appearance)

- R34 GTT neo turbo engine cover $150 $70 ( Tidy Up that Engine bay with a Clean Tough looking cover )

- R34 GTT water Bottle with what appears to be a attached windscreen squirter water pump $50 $40 ono

- R34 GTT Single horm when my 34 had its FMIC put on we had to remove 1 of the 2 horns on it still sounds better than most standard car horns. $50 $40 ono

Now the Eoi RIMS FOR THE RIGHT PRICE !!!!

Ok i have a very sexy set of start corp rims Up for grabs tyres included specs are bellow.

White Center Spokes with a chrome lip.

2x 18x8.5 +30

2x 18x9.5 +30

Price $750 Ono

More Pictures of the Rims Will be sent upon request .

My mobile number is 0416153371 all prices are Nogotiatble.

Cheers Tom

post-85341-0-51044200-1334716259_thumb.jpgpost-85341-0-13428400-1334716265_thumb.jpgpost-85341-0-25708000-1334716270_thumb.jpgpost-85341-0-16898600-1334716274_thumb.jpgpost-85341-0-16515900-1334716277_thumb.jpgpost-85341-0-23384700-1334716281_thumb.jpgpost-85341-0-39292700-1334716285_thumb.jpgpost-85341-0-14601200-1334716291_thumb.jpg

Bump, Price drop and Buy My shit :P Lol

Last chance before im gone overesas, got until 1st May, when I come back i wont be as negotiable and prices will go up :)

rb25det s1 motor, complete minus turbo, intake manifold, coilpacks. compression 145-160 on all 6 cylinders

Comes with ECU, Engine loom, Coilpack loom. Gates racing timing belt and pulleys done 20,000kms ago,

been serviced every 3-5000kms with full synth oil only) - $1000

rb25det s2 gearbox 86,000kms on it - $1400 or as a manual conversion kit $1700 (everything you need)

HKS GT2835r turbo (420hp rated, seen couple track days since rebuild made 290rwkw on another car)

kit including HKS cast manifold, Greddy ext. gate, screamer pipe, dump pipe, steel braided lines,

turbo intake and hot+cold side piping in lobster back stainless steel by AM Performance - $2100

AM Performance cat back exhaust system 2x2.5" in to 2x4" pipe with titanium tips - $900

Yellow Jackets coilpacks for s1 rb25 (all working, used for 1 year, fantastic coilpack, search forums) - $240

ORC Single plate clutch, 409 series unsprung center, used for 6months still in good cond - $400

Sparco sprint + R33 drivers rail 2 months old $650

Sparco Evo 2 Plus seat, no rails, brand new $500

Wlabro 550hp intank pump - $100

R33 BC BR Coilovers, used for 4000kms, like new - $900

R32 genuine GTR intercooler - 150

s2 dash surround with vents, buttons and clock, mint $80

s2 door trims with switches, mint $120

Edited by SkyHi_33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...