Jump to content
SAU Community

Recommended Posts

Hey skyline kids, I like to go down to pickles damaged Auctiuons every Friday when I get a chance this 93 R33 is up this Friday, unfortunately I wont be able to go see it, just thought Id put this here in case any-one else was interested-might be able to get a bargain 93 R33 @ pickles Friday 4th March

Edited by rickr333
  • 2 weeks later...

Hey all heres another one, R34, 4 door and auto :P ill be there just for fun, theres also an 89 wagon model too if any1s interested!!:thumbsup:

4 door auto r34

89 skyline EXECUTIVE wagon

Edited by rickr333

Hey all heres another one, R34, 4 door and auto :P ill be there just for fun, theres also an 89 wagon model too if any1s interested!!:thumbsup:

4 door auto r34

89 skyline EXECUTIVE wagon

r34 went for 4300+ fees woulda been about 4600, back left mag was missing (stockie on) and something bent at the back affecting str8ness of the wheel, also had rubber sprayed up the inside of both gaurds, pretty tidy besides that tho

Oh and the 89 wags went for 325.......BARGAIN

Edited by rickr333
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...