Jump to content
SAU Community

R33 Gts For Sale In Sa

2FST4U.R33
 Share

Recommended Posts

2FST4U.R33 Community Regular

2FST4U.R33

Posted
Posted (edited)

Hey all,

I have changed my mind and decided to sell my R33 instead of replacing the engine.

It's a 1993 R33 GTS series 1 with a suspeced spun bottom end bearing

asking 5K neg

ENGINE/DRIVELINE/ETC

  • Factory manual
  • Heavy duty clutch
  • Catback exaust with 3" cannon exaust
  • Engine oil & oil filter changed every 5,000-7,000 km
  • Gear box oil just changed
  • Brakes fluid just changed (inc bleading of all lines all the way through)
  • Recently changed radiator fluid
  • 18*,***kms (mostly highway, I live in Whyalla)
  • King Lowered Springs
  • KYB shock (less then 10,000kms old)

EXTERIOR

  • Full viva garage type 2 bodykit (light damage to front bar, nothing structural to the car)
  • 25mm flared guards front and rear
  • re-spray in blaze blue (outside and door jams only)
  • Xennon lights (low beam)
  • stock rims with near new tyres, can arrange 17" ROH rims with near new tyres for a bit more (cannot remember tyre type but about 250-280 ea)

INTERIOR

  • Very good condition, besides wear on right side of drivers seat and wear on handbrake "grip"
  • Genuine skyline floor mats (all 5)
  • Average sound system; 4" JBL parcel shelf, clarion cd player
  • Momo steering wheel with boss kit
  • Isotta shifter
  • Climate Control globes replaced with white 40,000MCD LED's (very bright white light)
  • Ignition light also replaced with 40,000MCD LED

THE BAD

Knocking noise from engine, 90% sure its a big end bearing. has not been driven since the noise started

slight power steering leak, one of the seals in the pump is on it's way out

flat battery, car has been sitting there for a couple of months

This car would either be great for someone as a first car or someone on their p's, although a new engine or a bottom end rebuild will be required.

Also would make a good shell if you have written off your R33 and just need to transplant parts.

Or just make some cash and either replace the engine or part it out

May be able to drop the price a little if you don't require the gearbox.

The car is currently located in Whyalla SA, can transport to adelaide at your expense

Best bet would be to text me on 0407971706

Cheers Luke

Pictures will be up 2moro

Edited by 2FST4U.R33
Link to comment
https://www.sau.com.au/forums/topic/355848-r33-gts-for-sale-in-sa/
Share on other sites
  • 3 months later...
Dado86 Apprentice

Dado86

Posted
Posted

Hey Champ,

Im interested in your car im a mechanic. I do alot of work on skylines.

The whole engine and drive line will need a rebuild.

make me a good offer without the gearbox and that.

Im after a shell to build a beauty.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...