Jump to content
SAU Community

Recommended Posts

Hey guys, I was hoping you could give me some opinions on whats going on::

what happened was this::

- I had a flat rear right tyre, so i took it to some tyre guys, and they replaced it for me.

- But in the process, they jacked my R34 GT up from the right side.

- Afterwards, I drove the the car immediately, and it was SO loud. like abnormally loud.

- Also, everytime i hit or released the brakes, there would be some kind of rattling noise. Sometimes even a screeching noise.

- So I had a look at the car, and i found that my exhaust pipe was kind of loose (ie. I could move it with my hands left and right without much force --> this also made the same, albeit softer, screeching noise)

I'm positive that the car did not sound like this before the guys at the tyre place jacked my car up, though I'm not sure how jacking the car up from the side could have caused this problem.

I was hoping for some advice or experience you guys may have had with this. Is this a big problem and should i be worried? Is the problem even with the exhaust/muffler ?

Any help would be greatly appreciated. Thanks in advance guys :)

Link to comment
https://www.sau.com.au/forums/topic/355903-loose-mufflerexhaust/
Share on other sites

- Afterwards, I drove the the car immediately, and it was SO loud. like abnormally loud.

- Also, everytime i hit or released the brakes, there would be some kind of rattling noise. Sometimes even a screeching noise.

- So I had a look at the car, and i found that my exhaust pipe was kind of loose (ie. I could move it with my hands left and right without much force --> this also made the same, albeit softer, screeching noise)

First thing i'd do is get under and check that all the exhaust bolts are present (check either side of the cat) and check the rubber mounts are still there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...