Jump to content
SAU Community

squeeking sound when clutch in

Trust33
 Share

Recommended Posts

Trust33 Grand Master

Trust33

Posted
Posted

Hi ppls i have a prob with my car.Whenever i put the clutch to the floor it makes this weird squeeking metal grinding sound and when i take it out the noise just stops....The clutch operates normally takes off fine and goes up gears fine.....i think it could be the thrust bearing given the way that my dad and his mate put it on.........Or could it be the spline at the front of the box?......Does the spline have to be greased before insertion or is it inserted dry......sounds good hey...

I am in need of some advice on the matter.....if any of you have experienced this or similar before..... :)

Link to comment
https://www.sau.com.au/forums/topic/35610-squeeking-sound-when-clutch-in/
Share on other sites
sherlock_nzl Apprentice

sherlock_nzl

Posted
Posted

Hi

Most likely thrust bearing noise.

There is a spigot bearing in the flywheel but I dont know what sort it is but it could also be that.

I usually put a very small amount of nickel antisieze on the clutch spline to ensure that the plate slides freely on spline, but even dry it will not make a noise.

Cheers

Trust33 Grand Master

Trust33

Posted
  • Author
Posted

its a brand new heavy duty xtreeme ceramic sprung button 5 puck.came with new bearing but still the squeek may go away after a while.it hasent even done 50km's yet.

i hope it does or else i will have to put up with it 4 a while

Let this be a lesson 2 every one.Get your bearing pressed on by a professional.it wont cost hardly anything but saving u the annoying sound........priceless.

:ufo: ''The chosen one''.

''The claw speeks''.

''owhwhwhw''

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...