Jump to content
SAU Community

Recommended Posts

Hi all

Have for sale my 19" wheels that just came off my car

Reason for selling: Tyres are to expensive where I live and wanted 18's

Condition: Pretty good, Theres some minor gutter rash on the right hand rear wheel, probably polish it out. Theres a little spot of gutter rash on the front left as well, this is probably the worst spot on the wheel but its only a small part. Can supply photos of what I'm talking about if you want but in general the wheels still look pretty good

They are 19 x 9.5 rear with a +38 offset. 19 x 8.5 Front with a +35 offset. Never had my guards rolled with these on and they look agressive without scraping all over the place. Probably wouldnt hurt to roll the guards but not necessary if you dont want to touch them (providing you have a 33 GTST)

Tyres are supplied, I have near new tyres on the rear, there only about 2 months old at the most (265's, Kendra tyres, cheaper brand but quite a good tyre) Front tyres still have plenty of tread but have suffered a bit of camber wear (235's, Nankangs, Again not the most expensive tyre but good enough grip)

Photos below:

89CAL1.jpg

DSC02273.jpg

DSC02278.jpg

Bought the rims with tyres for nearly $4000 when new, wheels are only 2 years old and just in need of a good clean and polish.

Asking $1500ono for the Wheels with tyres + I have either silver wheel nuts with a single lock nut or anodised blue tuner nuts (as sold by Taleb Tyres) + Hubcentric rings. PM me for a quicker reply :)

I'd perfer pickup (Mackay Queensland) but may organise freight at your expense

Will put up more photos later if I get the chance

Thanks

Callan

Link to comment
https://www.sau.com.au/forums/topic/360502-fs-koya-inox-r1-19-with-tyres/
Share on other sites

  • 1 month later...
  • 1 month later...


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...