Jump to content
SAU Community

R32 Gtr - Ticking Noise On Full Boost

smithy85

By smithy85,
in Engines & Forced Induction

 Share

Recommended Posts

smithy85 Community Regular

smithy85

Posted
Posted (edited)

Hi all,

Car is a R32 GTR still running standard turbos and actuators, and I am getting a really fast ticking noise coming from (what sounds like) the left hand side of the dash - only on full boost though, when the actuators are open. The noise is a plastic type of noise rather than a metallic sound (if that makes sense).

As far as I can remember, this has only been happening since the Greddy profec B spec II has been installed. It happens on both the high and low boost settings of 12 psi and 14.5 psi, and boost stays constant at its peak, ie: not fluctuating. PowerFC shows normal knock/timing readouts on the hand controller. Car has been tuned with this EBC, with none of the settings changed since.

My question: Is this simply just the noise the boost controller makes as it controls boost pressure, or could it be another issue that I should be looking at?

Any help would be greatly appreciated,

Cheers

Edited by smithy85
Link to comment
https://www.sau.com.au/forums/topic/361061-r32-gtr-ticking-noise-on-full-boost/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • MBS206
      MAJOR FUEL ISSUES 25det neo r32

      By MBS206 · Posted

      Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...