Jump to content
SAU Community

Recommended Posts

Keep the 20 and highflow a standard 20 turbo. Mine makes 219rwkw with a rb20 highflow, injectors, front mount, bigger fuel pump, microtech and full exhaust.

You've already got exhaust and front mount so all you need really is to upgrade your fuel system, tune, afm and to get a turbo that is capable of more then 15psi and you'll have around 220-230 rwkw.

Fuel pump $250

AFM $200-300

Injectors $300-400

Tune $850

Highflow $800-1000

Cam gears $150 plus new high tensile bolts $5

Easily done for under 3k.

I'd sell the rb25 turbo as there fine when standard on a 20 but once highflowed forget about it, way to much lag. Either a rb20 turbo highflow or hks 2530 is best for a rb20 imo. RB20 turbos are what like $50, hyper gear will do a high flow for around $800 and your laughing.

Get some cam gears to, thats my next mod. Apparently helps heaps with bringing on boost. I had some on my last car (hr31) untuned and i noticed a fair difference in power delivery.

I have gtr injectors and the resistor pack for sale to if your interested :thumbsup:

If you going to rebuild something rebuild a 30

if you dont need to rebuild then stick with your 20, just make sure you only buy stuff you can use when you get bored with the lack of torque.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...