Jump to content
SAU Community

Recommended Posts

Had / have two falcons

Xr8 and the xr6t

Was hanging around with a bunch of boys from the SA xr and fpv club . One dude had an xr6 t daily and a r32 gtr ( now a full racecar) got talking and was talking about shoe horning an rb neo into an r32.( forumember reading up )

Then I was workkng in sydney for 3 months and started looking at 32 gtrs not at all seriously ......... then somehow impulse bought a 33 gtr :-p

Um well its a bit different and obviously an older car and AWD ( no correcting angles with your right foot ;) )

Bit concerned about safety at this point. First thing I did was got it on a dyno and did oil and flush . coolant fuel filter etc

punched out 252 awkw @15psi ....while misfiring......... then put in Splitfires and a slightly cooler plug and shes all good. a=

major concerns at this point are slight underbody rust, and turbos....ceramic nervousness. given the boost level. Uni group seemed happy with it and its condition.

Once I get my gear up here and get some new tools going to do diffs, transfer and gearbox.

I think the clutch is slipping so that's on the cards at some point.



So in short. I am loving it, but I have some concerns and have had to fork out a bit of cash on it much to the missus disapproval. but the way I look at it is, it's a (long term) project. and I want it clean rather than modded first ( hopefully. though we know how mod bugs are).

Did i read that right ???? R33 LS1.......?????? Right boys fetch the holy water ( old engine oil from a PGC-10 mixed with R35 GTR brake dust) we have an exorcism to perform

Edited by ibrox90

I didn't go but I ran into the abom on the way to Brisbane :P

Sounded hot. Would have loved to have taken it on in the Caldina for a couple hundred metres to see if it goes as good as it sounds.

Nick's lucky we met on the Warrego :ph34r: :ph34r:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...