Jump to content
SAU Community

Recommended Posts

  • Replies 273
  • Created
  • Last Reply

Top Posters In This Topic

With the wheel specs noted, we moved on to replacing the grille. After Prach spent a couple of minutes fiddling with a few screws and clips, the old grille came out quite easily.

6311566499_e26314bf70_b.jpg

It kind of looked like a hillbilly with no front teeth when I closed the bonnet to see what it looked like without anything there.

6311567149_36b98b956b_b.jpg

6311567867_c9fe2fe6b8_b.jpg

The new one was pretty easy to snap in place, and a few minutes later the Ceffy had a markedly altered front-end appearance.

6312085318_ba94abd6ae_b.jpg

6312088694_52f4139220_b.jpg

6312089556_15e552003d_b.jpg

6312090966_6769f95cd7_b.jpg

6311571703_ff88b14e72_b.jpg

6283193733_083c4a20d3_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6096824
Share on other sites

There was a sedan sitting at the warehouse door with the front wheels on ramps, and a couple of guys working on it. I didn't have a good look at the time, but I think it's a Toyota JZX80 Cresta or Chaser, a model I don't recall having seen on the roads at all.

6317425975_aafb87aa7d_b.jpg

The style I'd most taken a liking to were these kind of mesh rims. There are so many variations of similar styles that I'm not 100% what these are, but I think they're Work Stitches.

6317947798_c98bfec78b_b.jpg

I had a look at the specs; the rears were 17x10s, -23. A full inch wider than the P1s, and with a negative offset, they would be very hard pressed to not stick out the guards like a 4wd. But we rolled one outside to see how it looked next to the car anyway.

One the way through the warehouse, one of the guys working there asked what car it was for. I said a Cefiro, and he had a bit of a 'That ain't gonna fit..' expression when I said it. Which is a fair point, the 17x9 P1s are pretty much flush with the guards as it is.

They did look good when Daniel rolled it across the rear wheel arch.

6317427211_953a53f635_b.jpg

6317427689_73cd963bbd_b.jpg

There was no way they would fit without some serious guard rolling, but it was fun to have a look anyway.

6317428247_005f8d5733_b.jpg

6317428929_2d65c8f841_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6097888
Share on other sites

After a bit of a poke around and with daylight fading, we started to head up towards Tea Tree Gully and into the foothills. After a fairly busy day physically, my stomach wasn't all that pleased with me doing more than usual, so I was feeling rather off for a while on the drive up.

Having syringed a couple of cups of water through my jejunostomy feeding tube before we left, the fluid had made its way south, and before we drove up into the hills, I stopped at a tavern for a few minutes.

6100425008_77bc3dd973_b.jpg

With sunset fast approaching, I jumped back into the Ceffy, and let Daniel take off in front of me. His Pintara makes around 160kw at the wheels compared to my Cefiro's 139kw, so he does have the upper hand power wise. Although I'd already been on several hills runs at this point, both by myself and with my girlfriend Sally, being able to head out with a mate in another noisy turbocharged car was awesome.

So we wound around some of the twists and turns for quite some time, enjoying the power, the fresh air, and the sounds of spooling turbos and crackling exhausts against the trees and rocky hillsides. Driving in the hills was enough fun to take my mind off feeling sick; although this generally doesn't work if you're in the passenger seat. By the time we made it into the small town of Gumeracha, the sun had just set, which meant there wasn't much light left for photos.

So we both pulled into the carpark adjacent to the town's main oval, and I grabbed my Nikon D300 and Nikkor 50mm f/1.4, and started rattling off some shots while there was still enough available light left.

Without a tripod or enough time to use one anyway, I just pushed the ISO up on the camera, while opening up the 50mm to let as much dusk light in as possible. It was really quite cold by this point, fortunately I had a jacket in the back of my car to wear, but Daniel was only wearing a t-shirt and shorts, and didn't find standing outside in the chilly hills air particularly comfortable.

So here are some of the quick snaps I took of our cars.

6100427406_dabd1592e2_b.jpg

6099886983_8b95073041_b.jpg

6099892767_f4b6d050c4_b.jpg

6100439856_71e3a54ec9_b.jpg

6099899471_4daa2b0f08_b.jpg

6099900579_6dae72d598_b.jpg

6099901925_e1914bd32c_b.jpg

6100449068_fdfde40a8f_b.jpg

6099917579_1426dda1cc_b.jpg

6099920905_6f30b85de1_b.jpg

6099922537_595784abc3_b.jpg

6100469398_f58684fa23_b.jpg

6099925675_fbfd702d52_b.jpg

6099927337_3fec66f147_b.jpg

After getting thoroughly frozen while standing outside taking photos of the cars, and the sky darkening too much for handheld photos, we headed back to Adelaide.

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6097892
Share on other sites

Yeah, spoiled for choice with that lot!

When I bought the Cefiro, I was under the impression that it already had a HICAS lock bar fitted. But while taking the rear wheel off, Daniel pointed out the fact I didn't actually have one. So the week after I made a trip to Sleeka Spares to pick up a lock bar kit.

http://www.sleekaspares.com.au/

One thing I like about visiting import/performance workshops, is that there are usually at least a couple of interesting cars around whenever you go. Walking across the road, I saw this late 1990s Toyota Corolla Levin coupe sitting in a yard opposite Sleeka Spares, a model that is very rare here.

6317646387_74a68e937d_b.jpg

There were a few carcasses walking through the gate, including this Toyota Celsior which had certainly seen better days.

6317647531_f9e4eb983f_b.jpg

I wasn't expecting it, but there were actually two Cefiros sitting in front of the shop, clearly both track only drift cars.

6318168248_2f954b24e2_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6099576
Share on other sites

6317649235_9c495345de_b.jpg

6318170034_978b7a04d3_b.jpg

6318170874_03c13377b1_b.jpg

6317651833_c9fa73a025_b.jpg

6318172626_51d9d023c5_b.jpg

The pink and black Ceffy belongs to Kelly Wong, one of the shop owners. A very small minority being a female drifter, she takes it to the track for some sideways action quite often, here's a short clip from Mallala.

6318173564_e7642a18a1_b.jpg

6318174372_994ee0a26e_b.jpg

Once inside I had a bit of a look around at the parts and stuff, and then bought the lock bar kit.

6317657515_7b03cc4c80_b.jpg

6317656563_96c09d2b72_b.jpg

6317655473_384fb1e85b_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6099584
Share on other sites

The Cefiro was becoming a daily driver now, and I drove it around to places fairly regularly. Sally and I visited a couple of friends who run a hip-hop/breakdance studio, and while they practiced I mucked around a bit taking photos using the mirror and reflections in the window, which made for some interesting shots.

6318151798_847b4c8430_b.jpg

6318155224_0654156d4d_b.jpg

6317633697_a8603d9707_b.jpg

6318156018_df5afd6f30_b.jpg

6318154396_a75c88467c_b.jpg

6318163120_dbc4f1dcaf_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6099588
Share on other sites

I got the itch for more hills driving after puttering around the suburbs, so on a decidedly grey afternoon I made my way up to Gorge Road, and proceeded to increase my fuel usage threefold.

It began raining fairly soon after I started to drive further east, which made the drive a bit different to the others. After the first section of Gorge Road it settled down a bit, and I pulled into a lookout area as the sun came streaming through the fast-moving clouds.

6322324561_e7c4762147_b.jpg

6322326947_92d967b2a8_b.jpg

6322329563_f1da18738b_b.jpg

While I do like having my car nice and clean, there was a certain amount of satisfaction in seeing the Ceffy dirty and dripping wet, with the exhaust burbling away as I snapped some pics; it's made for enjoyable drives like this.

6322859290_94a0d66b69_b.jpg

6322856648_fb31c32ec2_b.jpg

6322332087_b7cd33360d_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6100908
Share on other sites

It started raining quite hard soon after I took off, to the point that I pulled up in a slow vehicle lane on Gorge Road for a few minutes, as I couldn't see too well. It died down fairly quickly, and I went up and back on one of my favourite sections. With a cliff wall right next to the road, you get some pretty epic exhaust sounds when you put the foot down.

Since the roads were still quite wet, I was taking it fairly easy. But at the end of a gentle corner, I hit what must have been a patch of oil at about 50, and the car immediately snapped sharply sideways with no warning. With a rock wall on one side and guardrail on the other, I had to pull over a few minutes down the road to change my underwear.

6322335547_6fb34a7679_b.jpg

6322337859_978388f08b_b.jpg

6322339999_0dc3281079_b.jpg

6322342457_e8c0258ac5_b.jpg

6322872074_00c66570e5_b.jpg

6322874692_5a04abe043_b.jpg

Link to comment
https://www.sau.com.au/forums/topic/363022-my-ceffy/page/6/#findComment-6100918
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
×
×
  • Create New...