Jump to content
SAU Community

Is It Normal To Have To Adjust Engine Damper?

SargeRX8

By SargeRX8,
in General Maintenance

 Share

Recommended Posts

SargeRX8 Grand Master

SargeRX8

Posted
Posted (edited)

I had an engine damper on my old car. Adjusted it as necessary to fit the old car and it was fine. Took it off that and put it into my next car which is also a series 2 1996 r33, only this time I had to extend the length by about 2cm... Any particular reason why there is 2cm difference? Also dropped a f**king bolt and it didn't fall to the ground so yay Ive got a lingering bolt somewhere in my engine crevices.

Edited by SargeRX8
SargeRX8 Grand Master

SargeRX8

Posted
  • Author
Posted (edited)

I remember when I done the gearbox I loosened all the engine mounts n shit. I hope to God something is not out of balance. The car doesn't rock at all, and really I just installed this thing for looks...

If it is the engine mounts it would be a pain in the arse but I wouldn't need to remove the engine, just raise it and remove the old ones. I checked them out, they aren't cracked or anything but after looking at my old engine mounts. One of them was f**ked to the shit house. Passenger side one.

Edited by SargeRX8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...