Jump to content
SAU Community

[Sa ] 17X9 17X8 17 Inch Black 5 Spoke Rims, Avs / Advan Model 5, Perfect R32 Gtst Offset


Recommended Posts

Got a set of rims for sale, they are pretty standard 17x8 and 17x9 black 5 spoke rims, no gutter rash and in good condition. They need new tyres as the sidewall on the front right has a gash in it but holds air fine and the rear ones are fairly bald. They will drive you to the tyre shop but they certainly are not legal.

Here are some pictures. Not sure of the offset but they sit perfectly on an r32 gtst, sit about half a cm in the guards so they are legal and fill out the guards well, no scrubbing or anything like that.

Can possible organise cheap 2nd hand tyres if needed.

skyline4.jpg

skyline3t.jpg

skyline1r.jpg

Can send interstate but will probably cost a bit.

Asking $350 ono

Can call on <removed> or PM on here.

  • 1 month later...

Yep sure are, they are 5 stud though, won't fit an R31 (assuming that's what they are for).

Edited by Rolls
  • 2 weeks later...

$350, bargain, wish they were in NSW, can you get a quote on shipping please, if its not to much Ill grab them.

Post code 2173

Thanks Mark.

$350, bargain, wish they were in NSW, can you get a quote on shipping please, if its not to much Ill grab them.

Post code 2173

Thanks Mark.

Someone has just got in before you, if the sale falls through I'll let you know. Had them up for almost 6 months and finally two people want them at once haha.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...