Jump to content
SAU Community

Rays Volk Te37 Super Lap Sl 19X10.5+12 X2 Cheap!

douji
 Share

Recommended Posts

douji Rookie

douji

Posted
Posted

Hi all, I have got two Rays TE37 SL 19x10.5 +12 for sale. Fitted tyres on before and test run for 50km, found out they not the right offset for my setup. Now I am selling them for $1500 firm, they are selling for $1900 in the shop, minus waiting time. Tyres also available, Nitto Invo 305/30/19 x 2, run for 50kms, absolutely brand new, purchased them for $700 selling for $450. Pick up avalaible from Melbourne. SMS me at 0433285993.

CSC_0015.jpg

nitto_invo_5.jpg

douji Rookie

douji

Posted
  • Author
Posted

Don't happen to have any skinnier 19" tyres do you mate?

Nah sorry mate, only in 305/30/19, why go skinny if you can go for a big fat tyre look!thumbsup.gif

What is the pcd/ stud pattern for these?

5x114.3,fit most cars,which is including Nissan!

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...