Jump to content
SAU Community

Ducklip/wing Spoiler

GHT70 R33

By GHT70 R33,
in Classifieds

 Share

Recommended Posts

GHT70 R33 Enthusiast

GHT70 R33

Posted
Posted (edited)

R33 DUCKLIP/WING SPOILER

Will fit any r33 skyline s1 or s2

Has been sprayed nissan white(no clear)

1 peice fibreglass, when purchased it didnt have anything to fit it with so I have attached 2 factory plastic clips to the top(will fit right in your factory bootlid plastic clips),2 bolt ends to the back,and 4 screws or bolts can be also added where the 4 factory bolts go through on a r33 bootlid.

Its too big to post so only local buyers and local pick up thanks.

Im returning the car to stock condition so thats the only reason why im selling it,it looks heaps sleaky than the factory wings,cost about $250 new unpainted and with no fitting accesories but then postage is a fair bit on top cause of the size of it,so if your in the area pm me.

Can email pics at request(cant upload the pics are too big)

Located - Hervey Bay/Maryborough fraser Coast Qld.

PM me or msg 0401228867

Edited by GHT70 R33
Link to comment
https://www.sau.com.au/forums/topic/366815-ducklipwing-spoiler/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...