Jump to content
SAU Community

Sticking Speedo/ Rmp Needle

R33GTR88

By R33GTR88,
in General Maintenance

 Share

Recommended Posts

R33GTR88 Rookie

R33GTR88

Posted
Posted

So I just purchase an r33 gtr and I'm very happy with it but sometimes the speedo gets stuck at 60 also my rpm needles sits in the middle of the rev range or even all the way round at 10000. Does anyone know how to fix this? Or know a good place to get it looked at I'm in sydney.

Cheers in advance.

Link to comment
https://www.sau.com.au/forums/topic/367203-sticking-speedo-rmp-needle/
Share on other sites
Tony de Wonderful Veteran

Tony de Wonderful

Posted
Posted

I'd probably take out the cluster and clean the connections first.

The RPM is well known to f**k up. Most peeps but a new cluster but I fixed mine by desoldering and resoldering the chip on the PCB as per this link:

Tacho Fix

It could also have been pushed around 180 on the motor so you could try turning it back first. It should naturally rest at about the 7pm position (I think), then you push it clockwise over the 'stop' thingy to 0 rpm.

The Speedo could be a few reasons but I'd check for any mechanical obstructions like maybe the needle got bent a bit or the fascia has bent up slightly.

Otherwise get a new one from a breaker.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...