Jump to content
SAU Community

Recommended Posts

Hi people,

This problem has been happening for a while now. When the car is cold it is perfectly fine, runs as it should. Once it warms up, maybe 4-5minutes after ignition the problem kicks in.

As soon as the revs hit around 3000rpm it's like you have jammed the clutch down or you've put it in neutral, the revs just shoot up. If you hold the accelerator so it's not right to the floor then you can kind of get the car to accelerate but very slowly...as soon as you plant it, or even three quarters down, the revs fly without the car accelerating. The weird thing is that when I start the car in the morning and take it for a thrash it's perfectly fine. It was happening before I installed a brand new clutch, and it is happening still. Has anyone else had this problem? The car has done around 108 000 kms and is mod free. I took it to a garage for a general check-up and got them to do a quick check but they couldn't see anything obvious.

Any help or suggestions would be greatly appreciated.

Cheers,

Nick

Link to comment
https://www.sau.com.au/forums/topic/368321-1992-sr20det-180sx-problem/
Share on other sites

as i posted in his other thread about this (in the intro section), it will be the clutch. may just be an adjustment issue, but i'd say that it is knackered and the flywheel is most likely knackered as well. also if it was a 300zx clutch, from what i gather only the natro ones will fit, so it probably is no better than a stock sr20 clutch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...