Jump to content
SAU Community

Recommended Posts

Just had the line resprayed and new body kit fitted. Thought i would share.

the kit consits of vertex full body kits, blits ADR aprroved vented bonnet, R32 GTR spoiler.

Paint is light grey mertalic, TG0 paint code and is a factory colour.

Rims are R33 GTR @ 17x9+30 with 235/47/17

post-32868-0-59347900-1308963469_thumb.jpg

post-32868-0-82554200-1308963488_thumb.jpg

post-32868-0-73808300-1308963505_thumb.jpg

post-32868-0-50739700-1308963605_thumb.jpg

post-32868-0-68686600-1308963619_thumb.jpg

post-32868-0-51449000-1308963635_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/368923-my-new-body-kit-and-respray/
Share on other sites

  • 3 weeks later...
  • 3 weeks later...

Which rubbers do you mean exactly? I asked Nissan for genuine for the front and rear windscreens during my re-spray and was quoted roughly $660.

Told them to go f**k themselves. Politely.

Used a universal rubber mould and took great care to make it look good, and I'm happy with the result.

However my rear quarter glass moulds are a bit shitty and unfortunately they are encapsulated (part of the glass) so no chance of replacing them. Sigh.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...