Jump to content
SAU Community

S13 5 Stud Conversion, R33 Gts 4 Pots Or Gtr Brembos Both With Or Without Discs

megzz

By megzz,
in Wanted to Buy

 Share

Recommended Posts

megzz Collaborator

megzz

Posted
Posted

Hi Guys,

I am after the following to fit a R31

1) 5 stud conversion kit to suit s13 front and 5 stud conversion for the rear

2) R32 GTR/R33 GTS brakes or better (GTR Brembos) front calipers with or without discs.

3) RB25 breather hoses

4) RB30 oil dip stick

mungy Experienced

mungy

Posted
Posted

There is no kit for rear that I know of? All u can do from what I've found is redrill the axle of full custom work

vesh Proficient

vesh

Posted
Posted

I have a full 5 stud conversion kit from an S15. Comes with DBA slotted and cross drilled front and rear rotors with near new pads.

PM me if you are interested

familka gtr Experienced

familka gtr

Posted
Posted (edited)

Hi , I do have in Brisbane brand new 5 stud kit for S13 Front and Rear with OEM bearing in it.Manufactured for EU,JAPAN and US market .Easy to install, just swap them over and no other parts required except re drill your rotors to 5 stud .

With this kit you DONT need knuckles or arms or any other parts at all.

Brand new still in the box 800$ plus freight if need.

No made in china or some cheap backyard made .

Got full set of R32 GTR brakes calipers and rotors F & R

or R34 front full set rotors and calipers .

Edited by familka gtr

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...