Jump to content
SAU Community

Recommended Posts

Hey Guys,

finishing my rb30 rebuild, it has a nitto oil pump, primed the system by filling up the outside hose of the oil cooler and cranking the engine backwards until it had sucked up a good 500ml of oil, left the hose off and cranked it over.

Absolutely none of the oil comes back out the hose almost like its draining straight through the pump, any ideas??

could the gasket that goes between the block and the oil pickup be leaking causing the oil to drain out of the oil pickup? or an airleak elsewhere on the pump causing the problem?

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/371949-cant-get-oil-pressure/
Share on other sites

Did you put assembly lube or vasoline in the pump gears to help it generate more suction?

Why did you crank it backwards to suck in oil for? If you put some lube in the pump gears and pulled the plugs and injector lead and just wound it over it should prime normally.

Did you disassemble the pump by any chance and forget to do something up or left something out maybe?

didnt put in any lube or vaseline, was just told to prime it by filling the pump out section with oil and crank it back a few times.

The only thing im a bit sketchy on is oil pickup gasket, i think i may have used the old rb25 one as i found what looks like the new one on the floor when i was cleaning up and i had already dropped the engine in. If theres no other possible causes i may have to "attempt" to drop the cross member and remove the sump and try replacing it. I was kind of hoping that i may of had two new ones floating around as ive used a fair few gasket kits.

I know you cant drop the factory sump off with the cross member still there. If you dropped the cross member you could do it. Ive tried this before and couldnt get it off while the cross member was there.

Might be easier to just pull it all out and double check that gasket if its a big question mark. It would have to be a big leak for it to not prime up.

so you couldnt get it to pump oil by priming it and cranking the engine?? You had to actually start it to get it going?

I completely removed the oil cooler and standard oil filter backing plate and left just an oil filter using the rb30 threaded fitting. Drained the oil out of it and pumped it all back in through the 1/8th bsb thread on the side of the block next to the oil filter.. cranked it over and still nothing.

I might pump the oil back through the fitting and check that its getting to the head and try starting it for 5 seconds.

Edited by jarrod83

my old motor wouldnt make pressure cranking, even with a used oil pump full of oil and heaps of priming. even after 5 mins of cranking there was nothing, started it up and had pressure within 2 seconds. sometimes cranking just isnt enough, aslong as everything was assembled with lube and oil in all the right places it can run for a few seconds without pressure without doing any damage.

fk, cant believe it, but i primed the f*kker, started it, oil pressure just flicked straight up...

besides opening the oil pump and filling it with vaseline i couldnt have done any more to prime it for pressure, cheers for all the input guys, wouldnt of attempted starting it without pressure without it.

Jarrod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...