Jump to content
SAU Community

Recommended Posts

mandrel bent 2.5" mild steel custom made system. include 0-2 extra mufflers in the middle of the system, oval muffler on end.

will cost around 600 or so. just go to a local exhaust shop and get one made up.

this topic was covered in a previous post .... MANY times, in fact there was one just yesterday if you had bothered to read.

There is five different threads about exhaust systems for non turbo skylines on the first page of this section.

They need to put a sticky or something in huge bold writing because every single retard comes into this section of SAU and asks the same question.

gain performance through exhost?

easy mate, just make the piping as big as possible, 2.5" has been suggested cos its just too expensive to buy enough metal to make 5" piping. bigger piping = tons of air flying right through.

also sticking a whopping great big cannon will make your cars exhaust system be just as powerful as what the name suggests - A CANNON

your skyline will now fly

okay il be serious now, exhaust isnt a very great way to make more power. in fact anything n/a isnt a very good way to make more power.

this is why you are advised to SEARCH.

in fact, had you searched, you would also have found out that extractors are nastily expensive for the relatively little power they give unless you like to be in mid-high rpm ranges, and even then its still nothing special.

and if you at least did not say "cbf searching" - you would have at least avoided my sarcasm.

im picking up a nismo 2.5" cat back tonight. ill fit it tomorrow and tell you guys how the car feels.

im guessing it should be pretty good since it is a genuine nismo item for an NA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...