Jump to content
SAU Community

Recommended Posts

Hey guys,

as the topic suggests, just lookin for some photos/ideas from people that have already used a Full Race twin scroll manifold (im using a borg warner 83/75 single turbo)

Particularly in reguards to the air intake, compressor/pressure side plumbing and power steering reservoir location

Cheers

Joe

Edited by GTR_JOEY

Where does your manifold locate the front wastegate? There seem to be a number of iterations. I don't have p/s but intake side plumbing is the easy part - plumbing up the two gates etc looks to be the challenge (a challenge to do neatly that is).

as u can see the front waste gate is a pain in the arse lol

was also goin to run AFM's but it will be a difficult fit Y pipe/afm/ and filters with the turbo facing to the right

So the only option i can see atm is to run a D-jetro.. and good luck to the block whos doin the pluming for the wastegates :whistling:

TURBO IN!.zip

that should be a given, running a map sensor ecu.. btw awsome choice. need to get more bw data over here. im in the process of putting a 9179 on my gf rb25.. on a 6 boost. twin wg.= better but a pain in the ass to set up.

pic of turbon old manifold.

post-19586-0-55363400-1315996976_thumb.jpg

.

looks awsome mate... thats one fine lookin engine bay!! i may have to do something similar with my power steering reservoir

i have seen single set ups running AFMs, but didnt realise the dramas i was goin to have with the manifold pointing the turbo that way.

will be very interesting to see how the turbo performs in reguards to response with the twin scroll .. and yes get some data goin

  • 3 weeks later...

went in pretty good. wastegates are a pain. ps.. make sure you check what springs are in them. i orderd mine with 0.7bar springs.

i pulled them apart, one had 0.9bar springs and the other had 4 springs in it... almost took my head off when i poped the top off...

9179 on 6 boost, 3.5" exhaust. twin tial mvr44, spooling at 3k. straight to limiter by 4500-5k throwing p/s belts of... sounds awsome.

got the wastegates with no springs in them so didnt have an issue with that, but yeah there is a fark load of spring pressure in them haha

had to use 3 springs to get the 1 bar setting though

pretty handy how both ur wastegates are together, i have one facing the front which could prove interesting

how much power u making mate? u reckon the twinscroll makes a difference as appose to single?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
×
×
  • Create New...