Jump to content
SAU Community

Recommended Posts

Hi, my nissan r34 skyline gtt running stock boost, now when it is in low boost driving normally it sounds like a turbo should, i dont pretend to know much about turbo charged engines, but obviously as the turbine spins faster at higher revs it will make a different noise as to low boost. But for some reason my turbo is making a screaming noise which im not sure if it is normal or not as i have only had the car for a few weeks. any help would be appreciated as mechanics want to charge me $110 for a dyno. I havent had any other problems, no knocking on idle or oil leaks etc just the turbo noise, It probably is normal.

Link to comment
https://www.sau.com.au/forums/topic/377622-stock-rb25det-turbo/
Share on other sites

^ my car screams, is don is good. Get your post count up asap tho - we need more for sale threads to sabotage.

To OP: The problem is probably something to do with a gasket as mentioned, or something with a cooler pipe somewhere. It honestly wouldnt be an easy job for a turbo-newby to find and fix it.

Check all your pipes to see if theres anything loose or any hoses with cuts in them ETC. Otherwise you may want to see a mechanic as its likely to be coming from the turbo's exhaust gasket. I have had this happen myself more than once and it was the gasket every time.

Turbo/manifold nuts probably got loose - it happens from time to time. If that's the case, tightening them will fix the problem, but check it asap, or the gasket will be ruined by hot gasses and you'll have to take off the turbo.

Good thing is that it's not too hard to check/fix it yourself though - remove turbo heat shield and you'll see top two nuts right away. Bottom two are a bit more tricky to get to.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...