Jump to content
SAU Community

Recommended Posts

Hey all, up for sale is my long loved car.

Vehicle: 1997 Toyota Aristo Jzs147 3.0Q non turbo JDM.

Price: $7,000 or swaps. Wouldnt mind an s13 or r32

Kilometers: 151,000

Transmission: Automatic, MV Auto 1.5 Stage Shift kit

Colour: Pearl White

Location: Western Sydney

Contact number: 0466874737 (DON'T PM ME, ONLY CONTACT BY PHONE PLEASE)

Description:

The Good:

-HKS LS+ coilovers

-Mv Auto 1.5 stage shift kit

- 3inch to twin 2.5 inch cat back into quad dump pipe tips

- Cold air intake

- 18 inch 350z wheels

- new tyres on front, fairly new on rear

- new alpine head deck, can come with 12inch mb quart sub if you want

Mechanically great, has alot of power for an na, serviced every 5000km, transmission has had a fluid change every 5000km with new filter installed with shift kit about 2000km ago.

The car handles great with the coilovers, and they can still be set for comfort on the street.

I am the second owner in Australia, pretty sure it came into australia 3 years ago. The car was stock apart from the wheels when I bought it, so I have receipts for everything else.

Sale comes with most original parts, stock shocks, stock head deck (has tv), stock intake piping and air box. Tinted windows. Twin turbo front brake and rotor upgrade. Super comfy car to drive and gets about 600kms per tank.

Rego til 7th march 2012.

Selling because I want a change and want something smaller.

The Bad: When it was in japan, I am pretty sure that it was two tone, but the bottom tone got painted pearl white to match the rest of the car, the paint on the edge of the plastic trims on the doors has peeled off slightly, only on the edge, the paint on the rest of the car is fine though.

The drivers door has a tiny dent from when a tool box fell on it in the garage. The car was in a minor accident just after i bought it, I was driving and I was in bumper to bumper traffic and i accidentally rear ended the guy in front as I was changing lane, i was literally going 20ks, the damage was a slightly cracked headlight and the right guard was dented alittle, hence the replaced pearl silver guard. Both headlights were replaced with nicer headlights, there was no other damage and I still have the old headlights and damaged guard so you can see for your self how minor the accident was.

The front 350z wheels arent in the best condition, they have alot of gutter rash from the previous owner and the left front wheel has a slight buckle in it from a pothole (back when i had stock suspension in), this doesnt affect the driving of the car except it does vibrate very slightly at 85ks. The buckle can get taken out for 120 bucks I think it is.

The climate control has a loose connection as sometimes it randomly turns off, but other than that, it has aircon.

post-67519-0-19498300-1316932138_thumb.jpg

post-67519-0-19161200-1316932155_thumb.jpg

post-67519-0-70649500-1316932176_thumb.jpg

post-67519-0-88927100-1316932189_thumb.jpg

Thank you for looking :)

No low-ballers or tyre kickers please

Link to comment
https://www.sau.com.au/forums/topic/378194-fs-97-jdm-aristo-na-7k/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...