Jump to content
SAU Community

Recommended Posts

Want to buy some cheap 18's with no tyres that will fit 235/45/r18 and 255/35/r18 tyres on them. It's for a r33 gtst so +30ish offset would be best.

Will also trade my 18" Volk f-zero challenge wheels for other wheels that will fit onto my r33 gtst.

Volks wheels are 18" x 9" + 45 and 18" x 10" + 48. They are white with a chrome edge. There is a few gutter rashes on all of the wheels unfortunately.. As far as buckles go they are fine as per what OTR in Clayton said.

They come wrapped with 235/45/r18 and 255/35/r18 federal 595 rs-r's. Ive only done about 2,500km on them and have been pretty covilized on them so they've got pretty much all tread left.

TO fit onto my r33 gtst all I needed was 20mm spacers for the front, the back sits on fine. My car has king springs with apexi tmax shocks so I'm not sure how much lower my car would sit than standard..

Can swap for cheap wheels and tyres (as long as they're road worthy) plus cash my way, or just gimme something to roll on and buy the set, or just the wheels, or just the tyres, whatever!

post-67844-0-82950500-1321257817_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/383018-wtb-cheap-18s-or-wtt-my-volks/
Share on other sites

Hey mate might not be wat ur after but I hav a set of Blest Bahnsport Type D's in 18x8 and 18x9 in the +30's offset cant remember exactly, they are very much like work eurolines but hav tyres, pm me for pics if u like.

As above, will u split the wheels and tyres? If so how much for just the rims? Would they fit onto the size tyres I have posted at the start of the thread?

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...