Jump to content
SAU Community

Recommended Posts

What did everyone think of the efforts at the final drag meet for 2004 the other weekend? That little 4wd that nearly rolled spun me out!!! Was a bit disapointed with the skyline though. Started awsome, heaps off smoke, got into 4th I think by the sound of it, then spun and that was it. Anybody know what happned to it?

Was for sale. Sounds like its got the goods. If it the one in the trading post in Hobart it would want to go for the price!!!!

Link to comment
https://www.sau.com.au/forums/topic/38354-burnouts-at-drags/
Share on other sites

i think he was talkin $28K is that right? he is from launceston.

apparently it just lost drive, wether it was a diff or gearbox dunno.

its not that great a car, only runs 13s. its got fully rebuilt rb25 with forged internals, custom plenum, top mount T04 external wastegate. sounds like a truck. i like the veilside rims

Link to comment
https://www.sau.com.au/forums/topic/38354-burnouts-at-drags/#findComment-779765
Share on other sites

Good engine the old rb20's. I put one in a vl and was very happy with it. Never did get around to changing the diff ratio. Otherwise it was the same as another skyline that belonged to a good mate Mick from Speedy Tyres in launceston. His old red beast ran a best of 13.3 with truck front mount, 3 inch exaust and 14psi.

Now if only I could cram one in somthing lighter.

Link to comment
https://www.sau.com.au/forums/topic/38354-burnouts-at-drags/#findComment-792342
Share on other sites

Yep. Been out driftin in it allready. Goes really well, but will go even better soon. Should get into the hi to mid 12's. Will be suprised if it dosent. Its nothin special to look at but looks wernt hi on his list. Its go some good gear in it. Hes lookin for some coil overs at the moment. Drop in and see him if you know anybody or let me know through this forum.

Thanks

Matt

Link to comment
https://www.sau.com.au/forums/topic/38354-burnouts-at-drags/#findComment-799391
Share on other sites

yeh he took me for a run in it the other night, damn speed cut!

yeh i was talkin to him about the coilovers the other night, dunno if i swayed him or scared him!

yeh should do 12s when he has it sorted, pulled 160 rwkw's at reid racing last thursday, on 12psi pretty good considering still has factory ecu!

Link to comment
https://www.sau.com.au/forums/topic/38354-burnouts-at-drags/#findComment-801051
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...