Jump to content
SAU Community

Recommended Posts

Hey guys, I feel like shit right now, cleaning and prepping my car for the JDM cruise tomorrow, and I decided to use a small pressure cleaner to help get off some of the stubborn dirt.

Didn't really realise how strong the pressure was before I took off 2 inches of paint off the roof of my R34 GTT (white). See pics.

What is the best way to fix this without having to respray the whole car?

PIC 1

PIC 2

Temporary fix would be give it a light rub remove the loose paint then use touch up paint .

Long run the roof will need a respray sorry bud

I try to give a bit off distance when pressure cleaning

I blasted the paint of my front bar on my old supra and have always been hesitant since

My r33 (white) is flaking off on the roof mate, so i have to be extremely hesitant with my small pressure cleaner, and even the car lovers ones not to take it off. Now you have that mark, so will you.

Mine was like it when i bought it, and on the bonnet from stone chips too. I just looked up the paintcode (i think here) and bought some cans from supercheap. A couple of white ones, plus primer and clear coat. Rubbed it back a little, applied primer, then paint, then clear. Im sure you can read up on it a little more on here though for techniques, masking etc.

In the end, white is the easiest colour and in that regard you are lucky. Mine has lasted well over 12 months now (due again though) and looked decent. If you are a perfectionist, it probably wont cut it for long though. Good luck with it.

Not long after I had my 33 i was spraying the bonnet and right down on the bottom lip of it in between the headlights I had paint come off in a few sections. Easy temp fix with the right colour paint mine is white thankfully as well. Never used a high pressure cleaner again not worth it IMO just use higher quality car cleaning products

Edited by Jamie77

Never used a high pressure cleaner again not worth it IMO just use higher quality car cleaning products

QFT

A high pressure water cleaner can even be torturous when used as a bidet :woot:

fark :( spewing man, when u you a pressure cleaner its gotta be like only a fraction stronger pressure then ur normal hose pressure on max, otherwise ur kinda being stupid about cleaning... the stubborn dirt / grit in the future use a clay bar then polish after it to bring the paint up immaculate..

I have a gurney at my toyota work and i cleaned my first car i bought with it which had some minor stone chips, when i gurney'd it on high pressure it made the stone chip look bigger :(

spewing about your situation man but in the future use what i said earlier and your own pressure from your hands rather then something that's more used for driveways etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I might just check it out.. A Q among all those skylines.. lol
    • Time will tell, they're doing all the admin stuff at the moment. I've submitted all the required details, photos, etc.   I was under the impression that DC coupling is the best approach, i.e.: Solar Array -> Battery Invertor -> Battery  Where as AC Coupling is simpler, however less efficient, i.e.: Solar Array -> Solar Invertor -> Battery Invertor -> Battery
    • The price is really great for that kind of capacity. I thought similar setups cost way more. How's your efficiency been with the DC-coupling? I've heard sometimes there can be a bit of a performance loss.
    • Long time no random post about shit. So I went down this deep deep rabbit hole of battery storage for the home, ended up locking in a 41.9kWh Fox ESS EQ4800 with 9 units stacked. Battery uses Lithium Iron Phosphate, similar to what you find in those deep cycle boat/caravan batteries. And yes, why did I go with a cheapie brand and not like Synergy? simply because I don't plan to stay at this house for more than another 3~5 years.  The entire install, DC coupling (removal of existing invertor, connecting the current 6.6kW array direct to the battery invertor), new 8kW invertor is $6K all up (after all the rebates etc.). Going with this lot: https://www.aussiesolarbatteries.com.au/ It did seem a bit too good to be true, however seems like the Whirlpool community has vetted it and when it comes to this kind of stuff, they seem to be all over it: https://forums.whirlpool.net.au/thread/9pxj8482?p=38   I've requested for the battery to be installed outside, next to my meter board and not inside - rather have it combust and ignite outside lol.    
    • In Vic it would be a defect regardless of whether or not you cut a hole in the sheetmetal for the return pipe. The rules in Vic are shitful, and are generally interpreted as you can "make 2 mods to the intake system". Putting an FFP and an FMI onto it will almost certainly be seen as some huge number of intake mods. You really need to speak to an engineer before doing this stuff in VIC.
×
×
  • Create New...