Jump to content
SAU Community

Recommended Posts

FOR SALE - 1989 Nissan 300ZX Twin Turbo 2+2 Targa

3.0L V6 Twin Turbo - VG30DETT

4 Spd Auto

2 Door Coupe (2+2 Targa)

Black

Un-registered

No RWC

Can register for right buyer

102,636 kms on body

Freshly Rebuilt Motor (still being run in 5,000 kms on motor)

High-flowed Turbos

Re-gassed Air Con

Brand New Battery

(Two separate invoices for about $9k worth of work done on rebuild of the motor and turbos)

20 x 8 on Front with 235s

20 x 9 on Rear with 255s

Adjustable Coilovers in front end

After market exhaust

Blitz computer

Standard turbos rebuilt and hiflowed

New Nissan Purple Injectors

* Motor runs perfectly just like new after rebuild and new turbos.

Bad Points:

* Few body blemishes and could do with a respray

* Brake lights seem to be staying on (may need new switch behind pedal)

* Power steering bearing is gone, noisy when turning

PRICED TO SELL!!

$5,500 ONO

COME AND INSPECT MAKE AN OFFER!!

post-64736-0-80486400-1322701792_thumb.jpg

post-64736-0-37404800-1322701807_thumb.jpg

post-64736-0-72832600-1322701829_thumb.jpg

post-64736-0-04113600-1329187548_thumb.jpg

post-64736-0-59031900-1329187606_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/384571-1989-nissan-300zx-22-targa/
Share on other sites

  • 1 month later...
  • 1 month later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...