Jump to content
SAU Community

Recommended Posts

Howdy : FOR SALE-

1. Idler Bearing - New bearing, suits rb 25/20. Was going on rb25/30 but ended up using 2 tensioners. Great piece of mind on the next 100,000km service:)

$175 ono (will send interstate, see pics)

Brand new from Nissan ~$292

2. Xtreme Heavy duty clutch - 850kg pressure plate, sprung centre, 9 puk single plate. Installed by previous car owner, then used by myself for 6000kms. Good meat still on plate. Hasn't been checked.

$300 ono (will send interstate, see pics)SOLD!!

Brand new $500 from ACS

3. Lowered King springs - suit r32 gtst. Previous car ownerr had these on std. shockers. Great for lowering car :)SOLD!!

$200 ono for both pairs (will send interstate, see pic)

4. RB20det 5 speed manual, +2 piece tailshaft (ADELAIDE ONLY -sorry)

Excellent condition, No shudders, grinds, or scrapes. Comes with centre bearing, and yoke.

$600 ono

SEE LAST POST - ADDED 1 PAIR OF LOWERED SPRINGS!!

WHITE R32 : on my gtst the top of the wheel arches sat in line with the top of the tyre, or maybe a little just below the tread. Sorry no pics.

neil_se : i have heard that this clutch is basically rated one higher than the std clutch. I guess it would take somewhere over 200rwkw. If u've still got the rb20 in there it'll handle more than what u could throw at it :)

King springs sold.

Have another pair of springs that are lower than stockies, but not as low as Kings were. I took em off coz i put on matched set of Bilsteins.

Same deal as Kings, $200 ono.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...