Jump to content
SAU Community

What turbo is this?

Bazooka

By Bazooka,
in Engines & Forced Induction

 Share

Recommended Posts

Bazooka Rookie

Bazooka

Posted
Posted

Sorry for sounding stupid but I know very little about turbo sizing and what all the numbers mean.

I have in my possession a turbo that I was told is from an RB25 but noone knows for sure.

There is very little on it to say what it is so I hope someone on here can help me to decipher it.

The compressor housing has 45V2 on it and nothing else apart from "nissan".

The exhaust housing has 21U and 928A on it.

There are no AR numbers or anything.

Does this mean anything to anyone?

Link to comment
https://www.sau.com.au/forums/topic/38565-what-turbo-is-this/
Share on other sites
MattSR Community Regular

MattSR

Posted
Posted

Boost pressure has nothing to do with it - it's all about shaft speed.

If you increase the VE of the engine (ie a set of cams, or new inlet manifold, or exhaust system) you will find that the turbo will now fail at, say, 11 or 12 psi, as higher engine VE = more compressure RPM for the same boost.

:O

Cheers,

Matt

Sciby Experienced

Sciby

Posted
Posted

Well, technically boost pressure *does* have something to do with it, because on the stock turbo, at a given psi, you'd know that the shaft is spinning at X rpm... so we know that at around 13-14psi, the shaft on a stock r33 turbo would be doing the magic 'breakpoint' of X rpm, and would break itself into teeny bits and pieces.

I'm not following your example... feel free to enlighten me on what 'VE' is... but anyway... I disagree with it. :O

When the shaft is doing X rpm, it will fall apart, and you can use the fact that the *stock* impeller, will be pushing X PSI at that point. Even if it was spinning up faster or slower, that won't effect the shaft speed at which it'll break. Changing your cams or a manifold or exhaust system won't change the fact that the turbo will break at roughly X rpm, and thusly, will break when the stock impeller is generating 14+psi. Those mods won't change the spool profile of the stock turbo.

Edit: I've actually walked away and thought of something. I apologise, you're dead right: with a bigger intake manifold, tehre's more space for the turbo to fill up, therefore the turbo will be at Breakpoint rpm, but not reached the magic 14psi. Therefore, it will break at a lower psi. However, if the intake/manifold is stock, and the exhaust is changed, or the cams have changed, it won't break at an earlier psi, it'll just reach that psi faster.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...