Jump to content
SAU Community

Recommended Posts

Ok so I have lots of stuff I need to sell, all the r33 parts had 52xxxkm on the clock completely stock

1. R33 gtr RB26dett head completely stock as factory fitted from intake plenum to turbos, injectors, coils, covers the lot $1800

2. R33 gtr gearbox, standard flywheel and transfer shaft (missing shifter) $900

3. R33 gtr all standard Intercooler piping & bovs $200,

4. R33 gtr standard ecu, $250

5. R33 gtr whole front cross member 5 stud hubs (no brakes) $250

6. 2xstandard gtr intercoolers r32 and a r33 both have a few bent fins as usual. $300each

7. R33 gtr brake booster complete with pedal and all $150

8. Rb26 starter motor $150

9. R33 front TEIN coilovers $200

10. R32 vspek2 TEIN coilovers Full set (rear left is a bit knocky) $400

11.EOI R32 rb26 full reco head(like new) , and intake everything complete exc covers and turbo manifolds $1500

everything can be posted at buyers expense

Inbox me your mobile number for any pics

Located Taree nsw 2430

Edited by RB-20-VL
Link to comment
https://www.sau.com.au/forums/topic/387892-gtr-parts-nsw/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...