Jump to content
SAU Community

Recommended Posts

Hey guys!

I recently purchased a R32 GTS-T with no compliance plates for a cheap price, the car runs beautiful, but i'm a bit concerned. I took it for a fairly decent drive today (Illegally, shhhhh :P) to see how it ran, All the gears are fine, oil meter was fine, temp was fine. It definitely has power, turbo kicks in nicely and haven't noticed a problem with it. The car has had the idle problem but the previous owner "Fixed" it, so it'll idle at around 1.5 constant. But my main concern is the blueish smoke that comes out of the exhaust after letting off the accelerator while idling, as far as I'm aware it doesn't smoke when driving, but then again I'm not behind the car to confirm it fully. The blue smoke says to me, OIL!! It does leak a bit of oil from somewhere but not sure where abouts YET, although it's around the general area of turbo/power steering.

Could this be fried piston rings? or something a bit simpler. I'm only eighteen with no previous engine building experience but would love to take the engine out and rebuild it just to confirm my suspicions/nice learning curve.

Any help will be greatly appreciated!

Thanks, Braden!

Link to comment
https://www.sau.com.au/forums/topic/388975-blue-smoke-eek/
Share on other sites

Whilst mate is following your car at night, the blue smoke is constant if it's a rings problem.

If there's more smoke coming out under boost, then turbo seals are suss as well; not forgetting valve seals.

Comp test says what?

Oil useage going up?

Link to comment
https://www.sau.com.au/forums/topic/388975-blue-smoke-eek/#findComment-6199003
Share on other sites

Whilst mate is following your car at night, the blue smoke is constant if it's a rings problem.

If there's more smoke coming out under boost, then turbo seals are suss as well; not forgetting valve seals.

Comp test says what?

Oil useage going up?

I might setup my camera and test this as I won't be able to get a chance to drive it illegally for a while. But I do know that when I have the car sitting and I rev it, after I take the foot off the smoke comes out, can't see any if i'm holding a constant rev.

If it's coming out while driving aswell it could be

Rings

Valve seals

Or turbo seals

How much oils in the car it could be over full

Well I think the meter on the dash was at 4

Link to comment
https://www.sau.com.au/forums/topic/388975-blue-smoke-eek/#findComment-6199021
Share on other sites

Okay so I went out just then and started her up, let it warm up. The oil sat at just under "4" on the dash, I checked the actual dip and it was like half way up the stick, also had my brother rev it at a stable amount and there is no smoke today, not even when I let off the accelerator..

Link to comment
https://www.sau.com.au/forums/topic/388975-blue-smoke-eek/#findComment-6199023
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...