Jump to content
SAU Community

Recommended Posts

The stillen long tube intake will add at least 15kw at the wheels and is meant to be the best intake for the Skyline v36. This plus exhaust should give you close to 30 extra kw's.

Currently on special at stillen for $525 + shipping which is $200+

http://www.stillen.c...model=G37%202DR

Brand new, unused as decided to sell my car.Great opportunity to get it locally for less & without waiting.

$630 firm

Located in melb.

Edited by pauls
  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

hey,

This was purchased for the v36 coupe.

Not sure if these is any difference as stillen page mentions both coupe & sedan in the product details.

Don't know if there would be any difference in sedan & coupe front internals either.

I just had stillen USA check for me & they have confirmed 100% that the coupe & sedan intake kits are identical.

I can confirm slight differences in sedan & coupe piping.

Trying to find out & will provide further info.

The stillen long tube intake will add at least 15kw at the wheels and is meant to be the best intake for the Skyline v36. This plus exhaust should give you close to 30 extra kw's.

Currently on special at stillen for $525 + shipping which is $200+

http://www.stillen.c...model=G37%202DR

Brand new, unused as decided to sell my car.Great opportunity to get it locally for less & without waiting.

$630 firm

Located in melb.

Hey buddy I'm interested but I'm in Sydney can you find out how much shipping will cost I've placed an order for injen cold air but haven't paid yet 525 shipped if you can do same price or better we may have a deal

Hey,

I should be able to include shipping, however price is firm.Stillen R&D plus HP improvement makes This is the best intake you can get.

1329289173[/url]' post='6236306']

Hey buddy I'm interested but I'm in Sydney can you find out how much shipping will cost I've placed an order for injen cold air but haven't paid yet 525 shipped if you can do same price or better we may have a deal

Hey,

I should be able to include shipping, however price is firm.Stillen R&D plus HP improvement makes This is the best intake you can get.

Ok is it the one that has one filter sitting in front of grill or two filters

Two pods sitting next to each other behind the grill.

Each intake has its own filter.

Also has plastic brace, protector to stop any water getting on ram pods

Two pods sitting next to each other behind the grill.

Each intake has its own filter.

Also has plastic brace, protector to stop any water getting on ram pods

Buddy its cheaper for me to buy on line if you really want to get rid of them make me a good deal and ill buy them check out the price online delivered to au

Buddy its cheaper for me to buy on line if you really want to get rid of them make me a good deal and ill buy them check out the price online delivered to au

Unless they are the Gen 2 or Gen 3 there pretty cheap online Gen 2 $500 delivered Gen 3 525 so 630 is very high for the first one made Gen 2and 3 have improvements on power and all else get back to me soon if you are willing to make a good price no one will buy at 630no offence thanks

Read the subject title dude. Gen3. Purchased a few months ago & priced cheaper than what you can get it delivered from USA.You may wish to do your research & read the thread next time before commenting.

$525 gen 3 in America PLUS shipping which last I checked was around $299.

Edited by pauls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...