Jump to content
SAU Community

Recommended Posts

hey guys i have my Enkei Rpf1's forsale unsure of off set they came off my mates soarer im changing to some stockies for now. i work for a transport company that ships around Australia just let me know where you are and i can get it to our depots for you and you can pick up from there cheers pm me or text on 0402948881 heres an old pic on my car when i first got it

all the tyres nearly need to be replaced worn on inside edges a few big scrapes (before i got them) $500ono thanks guys

post-53831-0-30802400-1327998889_thumb.jpg

Edited by TwinTurboSupra+R32 Gtst
Link to comment
https://www.sau.com.au/forums/topic/390047-fs-enkei-rpf1-wheels/
Share on other sites

OK 19x8.5 lol and is the offset sound right j-42?? he's pics like everyone has been waiting for..

Also i have these Anz wheels i had them in my shed aswell 18.8.s i could not see a stamp for offset all tyres unroadworthy selling these for $300 they have a bit of dish i had to put them on my car for now as i have no wheels for my car pm or text for info no big marks on them cheers matt. they dont look to bad on the 32

my car has been sitting in my caport since oct so its real dirty thats why the wheels have cob webs and shit on them.

post-53831-0-48906700-1328335257_thumb.jpg

post-53831-0-75253700-1328335278_thumb.jpg

post-53831-0-28019700-1328335300_thumb.jpg

post-53831-0-44153800-1328335323_thumb.jpg

post-53831-0-10325200-1328335345_thumb.jpg

post-53831-0-49735400-1328335368_thumb.jpg

post-53831-0-74540900-1328335391_thumb.jpg

post-53831-0-45154200-1328335413_thumb.jpg

post-53831-0-76371400-1328335437_thumb.jpg

post-53831-0-31074200-1328335461_thumb.jpg

post-53831-0-65109000-1328335497_thumb.jpg

post-53831-0-07200000-1328335522_thumb.jpg

post-53831-0-71198800-1328335542_thumb.jpg

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...