Jump to content
SAU Community

Recommended Posts

Front 18x9 +15

Rear 18x10 + 22

Tyres: No wider than 235 front, no wider than 255 rear (depends on height, camber etc but this is a rough guide)

Also, see this thread, heaps of info and pics:

http://www.skylinesaustralia.com/forums/topic/84208-wheel-sizes-offsets-for-skylines

Front 18x9 +15

Rear 18x10 + 22

Tyres: No wider than 235 front, no wider than 255 rear (depends on height, camber etc but this is a rough guide)

Also, see this thread, heaps of info and pics:

http://www.skylinesa...ts-for-skylines

be careful with the front rims you choose, i have 18*9.5 +30 and the rim has been shaving the strut tower,

the rear is 18*9.5 +30 and is safe/flush, so you might be able to squeeze 18*10 +30 rear with some guard work

my car is lowish, guard is about inline with the line of the tyre tread

I suggest you to not go staggered offset - for some reason, it does not look nice on R33s.

Go Rear 18x10 + 22 all round and go 255 or 245 tyres all round.

What are you on about? You will struggle to fit 10"+22 on the front, especially with such a fat tyre. Stop giving out bad advice mate

be careful with the front rims you choose, i have 18*9.5 +30 and the rim has been shaving the strut tower,

9" +15 has 21mm more inner clearance than a 9.5" +30 :thumbsup:

What are you on about? You will struggle to fit 10"+22 on the front, especially with such a fat tyre. Stop giving out bad advice mate

9" +15 has 21mm more inner clearance than a 9.5" +30 :thumbsup:

I have the same rims and tire profile on my car right now. But my guards are rolled and flared so maybe you are right, just realise the poster's car is a GTST so may not fit like yo say. My bad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...