Jump to content
SAU Community

Recommended Posts

ok brought this off the forum a month or so ago, nd have decided to go a different route. so putting it up for sale. $450.

got some cobalt gauges for sale (Boost, air/fuel nd oil pressure) looking at $350 for all three, or $125 each

standard front nd rear S2 sway bars $100

set of 18" mags mesh type which were on car, front tyres 95% tread, other camber worn ($500)

got a momo steering wheel here used for about 20min of driving on 1 day $100

momo metal pedal covers (manual pedals) $100

momo gear knob $50

Recaro reclinable race seat on S13 rails. similar design to the supra RZ race style seats. $400

2 way LSD (think its nismo) used in my 180 for about 4 months $600 (6 bolt drive shalfs)

whole heap of standard 180 parts here as well

prefer local pick up. north east suburbs of adelaide. can meet some where if possible

text me on 0405504778 or pm on here

na momo isn't off a stagea. its just a basic momo steering wheel. ill see if i can find a model number nd stuff. as its tucked away in the shed

i only got the e-manage and loom to plug nd play with standard ecu, will be coming out of car within next day or so.

nd pics of wheels:

http://a7.sphotos.ak.fbcdn.net/hphotos-ak-snc7/383932_267285549996058_100001438467673_775680_1209637871_n.jpg

  • 3 months later...
  • 1 month later...

Most stuff still here pm for info, not on much. Wheels, ns steering wheel gone. Make offers on everything need the money as moved out nf need to pay bills. Will have trouble with posting stuff so prefer local pick up or I can bring some stuff over to Sydney in August when I go over

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...