Jump to content
SAU Community

New Genuine Bosch / Jecs Z32 Air Flow Meter Afm - $285 Incl. Delivery

VultureMotorsport
 Share

Recommended Posts

VultureMotorsport Mentor

VultureMotorsport

Posted
Posted

GENUINE Z32 AIR FLOW METER

- Large 80mm diameter - most common AFM upgrade

- Genuine BOSCH/JECS - manufactured in Japan
- Wiring diagrams also available on request
- Can also supply TOMEI Plug $40 w/ wiring OR BOSCH Plug $30 w/ no wiring.
- OEM # 22680 30P00 (VG30DETT engine)

$345 $285 incl. Delivery >> SAU Special

BUY_BUTTON.gif

* This is an Australian delivered product with a full national warranty.


AFM-029_400.jpg


AFM-029_box.jpg

  • 3 months later...
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

New batch just in!

Feel confident in that you are purchasing a Genuine Z32 AFM.

BOSCH Plug - $25 with same day dispatch!

  • 2 weeks later...
  • 1 month later...
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

deilvery to sydney 2763 with plug to suit r34 in stock?

Hi,

Tomei Plug w/ wires would be $320 or BOSCH Plug w/ no wires would be $310 both incl. delivery.

Being a larger AFM then the stock 70mm one some modifications will be required.

- Brendan

  • 1 month later...
  • 6 months later...
  • 1 month later...
Serpandrew Rising Star

Serpandrew

Posted
Posted

So the tomei plugs have wires that have to be cut/soldered into the original afm wires, and the for the bosch connectors you have to undo the wires from the original connector and push them into the bosch one?

VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

So the tomei plugs have wires that have to be cut/soldered into the original afm wires, and the for the bosch connectors you have to undo the wires from the original connector and push them into the bosch one?

Hey!

Correct the BOSCH plug comes with no wires and the Tomei unit comes with wires. In most cases the Tomei one is an easier choice to work with.

- Brendan

  • 3 months later...
  • 11 months later...
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

100% Genuine unit's only!

​.... for those note sure if what they have is a genuine unit just check if the sensor inside has a red coloured band around it!

  • 2 weeks later...
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

Hey mate, do you have any plugs to for the Z32 to be used on a S15?

Yo!

Easiest option would be a Tomei plug which you can wire up to the original harness.

Let me know,

Brendan

(VM)

  • 10 months later...
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...