Jump to content
SAU Community

Check Engine Light Pfc

SargeRX8

By SargeRX8,
in General Maintenance

 Share

Recommended Posts

SargeRX8 Grand Master

SargeRX8

Posted
Posted (edited)

I was just driving home and my check engine light came on. It came on first solid for a few seconds then went away. Few seconds later it came on again, solid then went away. I went to stop the car and the idle was hunting really bad. I tapped the throttle and it stabilized. Then it came back again. Each time I was low in RPM, low speed(probably 2nd or 3rd gear max). Car has a Power FC. Hand controller showed 5 knock(the light was solid, not flashing), injector duty was low and temp was about 74c when I shut it off.

Any ideas what can trigger the light? I guess the only hint is the hunting idle, which it has never done before... Only thing that has changed since this happened were the rear brake pads... Where the hell do I start? The car is low on fuel atm, but no warning light for fuel and I wasn't giving it any. Any way to diagnose if its the TPS or AFM? What else throws up the warning light which could cause the engine to hunt?

The only thing I can think of is throw the standard ECU in there and do the diagnostic, but Ive got a Z32 AFM and Nismo injectors. I can swap out the AFM but I can't swap out the injectors... Will it throw error codes about the injectors?

Edited by SargeRX8
Link to comment
https://www.sau.com.au/forums/topic/392948-check-engine-light-pfc/
Share on other sites
SargeRX8 Grand Master

SargeRX8

Posted
  • Author
Posted

This is solid for about, well I can't time it it just stays on solid for at least 5 seconds.. Flashing CEL means something is maxed, solid means sensor failure. I just tested my tps, it seems solid, I can increment it .01v at a time to 4.06v.

SargeRX8 Grand Master

SargeRX8

Posted
  • Author
Posted

Cool, it won't do it anymore. f**kING SHIT f**kING PIECE OF SHIT.

I was reading on the net the way you diagnose with a power FC is go to the sensor page, anything which triggers the CEL is on that page and either you look for something out of the ordinary or you look for something which is highlighted black which means its at fault, not connected or not working.

I wish there was a list of EVERYTHING that triggers the light to come on solid, then I can check them out one at a time and tick them off.

SargeRX8 Grand Master

SargeRX8

Posted
  • Author
Posted (edited)

take a photo of the sensor screen on the pfc whilst its running shit if possible and post it up

I took a photo of it normal, now I'm waiting for that engine light to come on so I can snap a photo of it in that state. Judging from what I have read, if the check engine light comes on, the issue WILL be displayed on the sensor screen on the commander(or at least values which are out of the ordinary).

Edited by SargeRX8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...