Jump to content
SAU Community

Recommended Posts

Have a few sets of wheels looking to offload, held onto them to use on track have since sold my car so dont really need them

17 inch Stern 5 x 114.3 wheels cant see any offset

1 x 235 tyre still good tread, 1 x 255 tyre tread worn other 2 tyres popped rims have some gutter rash $150 set of 4

17 inch mesh rims 5 x 114.3 17 x 8 and 17 x 9 rims 235 and 255 tyres, tyres fair some tread left rims again have gutter rash $200 set

17 x 8 inch wheels 3 only tyres still ok $100 for the 3

16 inch BBS wheels bad gutter rash tyres not best $100

Also have a few 16 and 18 inch tyres here do cheap from $10 as need space

I am in Carlton in sydney for pick up

Can freight wheels if need be

Tks

Daniel.

post-3004-0-55725300-1331605042_thumb.jpg

post-3004-0-25461900-1331605049_thumb.jpg

post-3004-0-99503100-1331605055_thumb.jpg

post-3004-0-29329500-1331605067_thumb.jpg

post-3004-0-34357400-1331605092_thumb.jpg

post-3004-0-37896000-1331605482_thumb.jpg

post-3004-0-74584000-1331605510_thumb.jpg

post-3004-0-83218000-1331605515_thumb.jpg

post-3004-0-54307400-1331605520_thumb.jpg

post-3004-0-10086100-1331605528_thumb.jpg

post-3004-0-92791900-1331605558_thumb.jpg

post-3004-0-31012400-1331605598_thumb.jpg

post-3004-0-51981100-1331605605_thumb.jpg

post-3004-0-86933800-1331605612_thumb.jpg

post-3004-0-36592100-1331605621_thumb.jpg

post-3004-0-64195200-1331605629_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/394575-5-x-1143-17inch-wheels-and-tyres/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...