Jump to content
SAU Community

Power Enterprise \ Denso 800Cc Top Feed Injectors - Need Lag Times

The Mafia

By The Mafia,
in Engines & Forced Induction

 Share

Recommended Posts

The Mafia Grand Master

The Mafia

Posted
Posted

hey everyone

I have been googling for about half an hour and can't find anything. well not yet anyway.

I need to know the lag times for this injector so that I can apply adjustments in a powerfc.

This is the model number:

1001-87096

800cc top feed

Lime Green

Can anyone help?

Thanks

Moodles2 Grand Master

Moodles2

Posted
Posted

Since SARD just repackage Denso injectors like PE:

63566 (6 X 800cc)

Nissan SKYLINE (BNR32, BCNR33,BNR34 RB26DETT) - 800cc - Top, Low Impedance, 2 Hole, Yellow - Green (Pic 6 ) Time 1.10 msec

Tangles Grand Master

Tangles

Posted
Posted

you've got your answer - so Ive just got to add this

I love these threads.

You love the noise - and put the BOV on the car to be a wanker. Its scientifically proven that if you're a wanker, the first thing you do when you buy a Skyline is install a vent to atmosphere blow off valve, to advertise the fact that you are indeed, a wanker.

Do you even know how the Nissan air intake system works? There is an AFM that measures the air entering the engine. the Stock BOV recirculates FOR A REASON. When your duck whistle, twisty whooshy twirly, dick pulling, sparkly, spinny, shiny, noisy, fuleh sic, wank off valve opens, it dumps air that the engine has measured and allocated fuel for. When only half the air gets into the cylinder because the air it measured is at the street corner where you sped up erratically and backed off because you saw some women on the corner, thinking that when they heard your BOV they'd get naked and run and dive into your car, the engine is now overfueled and under oxygenated, and stalls, backfires, and carries on. You know why? Because you've created a MASSIVE AIRLEAK on a system that will not run with airleaks.

Do you like that fact that you will foul your plugs constantly?

Do you also like attracting the cops attention?

Do you like the risk of being defected and having to pay money for a BOV that didn't need to be There?

Do you like the fact that you are just making skylines more hated? (And don't worry, its almost a guarantee that you'll drive through the main street of town making it release "because you like the wank off sound")

Do you like it how women love the sound, get naked and dive into your car as you drive past?

Do you think SAU will be happy about another "My car is running rough, I only installed a duck whistle, twisty whooshy twirly, dick pulling, sparkly fuleh sic wank off valve" thread

love it; no offense meant ;)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...